Search:

Type: Posts; User: froggymaxx

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    370

    If you can run it buy it.....100.00 is a good...

    If you can run it buy it.....100.00 is a good deal....
  2. Replies
    1
    Views
    392

    Spiral cut gears?

    Anyone ever heard anything good about them? I keep blowing the rear diff .3 so far and I'm tired of pulling it apart.they have all been perfect when they go in but only last 4 or 5 runs.
  3. Replies
    13
    Views
    3,110

    An e Marx will always be relevant at my house and...

    An e Marx will always be relevant at my house and the new Maxx is way out my range on price....too much money for a 4s truck...I run a mamba black 4s in my e maxx and it's more than relevant against...
  4. Replies
    4
    Views
    787

    The platinum is awesome...I had one. Olds 97 is...

    The platinum is awesome...I had one. Olds 97 is right a big block is the way to go I've built several.Steel gears, sway bars,rpm arms,tru trac in the rear,17mm hubs. You have a much better selection...
  5. Replies
    5
    Views
    4,671

    Ok that looks like what I was thinking...I...

    Ok that looks like what I was thinking...I believe it's a 36 spur. But realy bottom line . should be if I run standard revo gears in the cases then the revo stock spur would be a good start if it's...
  6. Replies
    5
    Views
    4,671

    So if I run an all revo set in the slayer tans...

    So if I run an all revo set in the slayer tans case....1\8 buggy wheels run the revo or slayer spur?.....14 or 15 on the CB I have both
  7. Replies
    5
    Views
    4,671

    Force .30 slayer ......gears question

    I want to put steel gears in my slayer I have a force .30 in it am pretty sure the trans won't handle this power for long.I'm running 17mm hex's 10mm extended, Badlands on buggy wheels. putting 70 or...
  8. Thread: how hot?

    by froggymaxx
    Replies
    3
    Views
    181

    Ok thanks,it's running 180 ish should I drop a...

    Ok thanks,it's running 180 ish should I drop a tooth or 2 on the pinion ?
  9. Thread: how hot?

    by froggymaxx
    Replies
    3
    Views
    181

    how hot?

    Ok guys been a while since I have played with a brushed motor. How much temp is too much? Thanx guys.:confused:
  10. Replies
    12
    Views
    442

    I would also go to a bearing in the bell...

    I would also go to a bearing in the bell crank,the alloy duel disks seem to cool faster than stock disks.
  11. Replies
    12
    Views
    1,740

    I did a frank'n build some time back....I can't...

    I did a frank'n build some time back....I can't stop putting Big Blocks in small trucks lol....I did a boosted .28 in CRT .5. We called it the Animal...My on going one is a .32 in my short...
  12. Replies
    12
    Views
    1,740

    Well done...!!! That is a clean build.Video...

    Well done...!!! That is a clean build.Video next?.....
  13. Thread: Big Block?

    by froggymaxx
    Replies
    21
    Views
    2,691

    Al.....I remember your posts from way back...lol...

    Al.....I remember your posts from way back...lol nice to see you again on the forums.I happended on to a new era mount and put a force .32 in my short chassis slayer.Not finished yet working on a...
  14. Replies
    9
    Views
    597

    I had a similar problem,turned out the keeper...

    I had a similar problem,turned out the keeper clips to hold the wrist pin...I had one come out and wedge itself between the piston and sleeve.So check them out.
  15. Replies
    8
    Views
    1,044

    I run those filters on my jato and 1/8 buggy. on...

    I run those filters on my jato and 1/8 buggy. on road only cleaned and oiled each time out I like them.
  16. Thread: 3906 diffs

    by froggymaxx
    Replies
    2
    Views
    176

    3906 diffs

    Will the newer sealed diffs work in the 3906? The rear is blown in a 3906 And I want to buy a complete diff and replace just the one.Do I need to use the old style or no?...:((
  17. Replies
    5
    Views
    518

    Thanx guys....good food for thought.

    Thanx guys....good food for thought.
  18. Replies
    5
    Views
    518

    Realy...nobody has an answer?...I would really...

    Realy...nobody has an answer?...I would really like to run lipo,not stuck on brushless at this point, but would love run time.can I run 2 2s in this 14.4 volt yellow esc? It's a 3906 flat chassis...
  19. Replies
    3
    Views
    210

    Nope ....pull that bad boy out and you have an S...

    Nope ....pull that bad boy out and you have an S Maxx....
  20. Replies
    5
    Views
    518

    Yellow EVX-2 ??

    Ok guys An old friend just came home...lol...I got back after many years my old E Maxx.It has EVX yellow ESC. Now for some reason I was running 16.8 volts in this truck.I just looked at the ESC and...
  21. Replies
    28
    Views
    2,401

    It's going very well.Everything was mocked up and...

    It's going very well.Everything was mocked up and fit good,So now tear down and install the RR steel gears.Trying to get my 1/1 sand rail ready to sell so not much time spent on the slayer.But back...
  22. Replies
    28
    Views
    2,401

    Awesome Nizz....!!!!! :thumbup:

    Awesome Nizz....!!!!! :thumbup:
  23. Replies
    20
    Views
    1,344

    Ok here is some food for thought ....When the New...

    Ok here is some food for thought ....When the New era mount is in the BB clutch bell position(rear most) On the slayer with the force engines it clears the arm at fill compression strait down.....But...
  24. Replies
    20
    Views
    1,344

    Wow I tried to post a pic again to no...

    Wow I tried to post a pic again to no avail...lol.....
  25. Replies
    20
    Views
    1,344

    I have to get some pics up soon..the truck is...

    I have to get some pics up soon..the truck is looking good...The .32 is in.!!!..the RR wide ratio gears are on the way,the exhaust is mocked up,and appears it will fit under the body...YAY no hack...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4