Search:

Type: Posts; User: Darth Beavis

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Replies
    238
    Views
    22,158

    Ahmmm...SHUT UP, BUTT-MUNCH!:lol: It's a funny...

    Ahmmm...SHUT UP, BUTT-MUNCH!:lol:

    It's a funny story involving a small workshop, lacquer paint, and no ventilation.
  2. Replies
    238
    Views
    22,158

    Thanks, Max. I find your lack of teepee for...

    Thanks, Max.

    I find your lack of teepee for my bunghole... disturbing.
  3. Replies
    238
    Views
    22,158

    Hey, El Sob, Any chance we could get some...

    Hey, El Sob,

    Any chance we could get some photos of how you mounted that front Raptor bumper to your 4x4? I want to do that to mine, but so far haven't been able to figure out how to make it...
  4. Replies
    6
    Views
    817

    You did the same thing I did. It's great for...

    You did the same thing I did. It's great for bashing in the dark!
  5. Replies
    21
    Views
    1,435

    Try removing the clips from the inside of the...

    Try removing the clips from the inside of the battery compartments. That might free up enough room to allow them to fit.

    Da Beav
  6. It's a Gen1 sway bar kit, with longer screws, and...

    It's a Gen1 sway bar kit, with longer screws, and some washers to keep the plastic part in the rear from bowing.
  7. The only must-haves for me were the red 2255...

    The only must-haves for me were the red 2255 servo, chassis brace, and a sway bar set. I also upgraded to the steel spur gear, as my plastic one was starting to show a little wear, and I didn't want...
  8. Replies
    9
    Views
    669

    If you have the Bluetooth module, you can restore...

    If you have the Bluetooth module, you can restore self-righting. Change the E-Revo to another model, like a Slash 4x4. Then, power everything, including your phone down. Wait about 1 minute, then...
  9. Thread: My 2.0

    by Darth Beavis
    Replies
    57
    Views
    3,746

    You might try either some Teflon plumber's tape...

    You might try either some Teflon plumber's tape on the threads, or removing the balls, putting a small amount of super glue down the hole and letting it dry, then threading the balls back in. That...
  10. Do you have the part numbers for those? There's a...

    Do you have the part numbers for those? There's a trip to Lowes in my future! :D
  11. Replies
    29
    Views
    1,741

    My 2.0 is running a single 2255. I wouldn't...

    My 2.0 is running a single 2255. I wouldn't recommend a 2255 on the MXL-6s, though. I did that and it cooked the BEC. The VXL-6S has a much more robust BEC, so you should be fine running it on that...
  12. Replies
    4
    Views
    264

    I saw someone had drilled holes in the underside...

    I saw someone had drilled holes in the underside of the wing end plates, and installed a set of wheelie bar wheels. It seems to work well to protect the wing. An upside is EXTREME wheelies! :D
  13. Replies
    14
    Views
    684

    Integy needs to drill and tap them for the sway...

    Integy needs to drill and tap them for the sway bar set. I'm glad to see their parts aren't just pretty.
  14. Superglue. Threadlock will attack the plastic.

    Superglue. Threadlock will attack the plastic.
  15. Replies
    4
    Views
    706

    I'm running a Traxxas 2255 with the stock arm. I...

    I'm running a Traxxas 2255 with the stock arm. I just removed the servo link on the side without the servo. This way I can always go back to dual servos, should I feel the need for more misery in my...
  16. Replies
    29
    Views
    1,023

    When I worked at Radio Shack back in the mid-90s,...

    When I worked at Radio Shack back in the mid-90s, we got a shipment of soldering guns that had "Weller" stickers on them.

    The area manager almost stroked out when he saw them on the shelf. :lol:
  17. Replies
    11
    Views
    480

    I use MIP bits and a ratcheting handle (Harbor...

    I use MIP bits and a ratcheting handle (Harbor Freight has some good quality, cheap ratcheting screwdrivers), or an electric screwdriver.

    I use a Ryobi 4v, and it does great. I think I'm going to...
  18. Replies
    33
    Views
    1,225

    If you're gluing tires, it's a good idea to...

    If you're gluing tires, it's a good idea to scuff the bead with a Scotchbrite pad or some fine sandpaper. Then wipe with some acetone or lacquer thinner to remove all contaminants--just be sure to...
  19. Replies
    13
    Views
    665

    If you have the app and bluetooth module, dial...

    If you have the app and bluetooth module, dial brakes back to about 50%. It will still stop hard, but it reduces the cartwheel factor. On my next outing I'm going to try dialing brakes back further...
  20. Replies
    4
    Views
    335

    Is it the ESC or the receiver that won't update?...

    Is it the ESC or the receiver that won't update? Better call Traxxas. They can help you sort it out.
  21. Replies
    0
    Views
    295

    2.0 lighting

    Currently, I'm running a Summit front and rear bumper, with the LED lights, which works, but like all good motorheads, I WANT MORE. I've been thinking about adding the UDR light kit to my 2.0, but I...
  22. Replies
    6
    Views
    575

    I had (past tense) an MXL-6s, running the single...

    I had (past tense) an MXL-6s, running the single Traxxas 2255 servo. It lasted about 20 minutes, before the on-board BEC let go. I'd suggest getting an external BEC, if you love your MXL.
  23. Replies
    16
    Views
    2,317

    Suggestion--turn in your pillowballs 1 turn. That...

    Suggestion--turn in your pillowballs 1 turn. That seems to help stop the driveshafts popping out. I haven't had the rod end problem, but I also pulled mine apart and replaced with new rod ends. I...
  24. EXACTLY! I have a set of Trenchers, but...

    EXACTLY!

    I have a set of Trenchers, but they're too big and heavy. I went back to stock tires until something better comes along.
  25. Replies
    15
    Views
    1,622

    Do you have a part number? Inquiring minds want...

    Do you have a part number? Inquiring minds want to know!:lol:
Results 1 to 25 of 34
Page 1 of 2 1 2