Search:

Type: Posts; User: grizzly03

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    45
    Views
    908

    Looking good. Install the yellow wire on one of...

    Looking good. Install the yellow wire on one of the 4 screws that hold the engine to the motor mount. Best place is one of the 2 on the fuel tank side (under the starter motor). It's the ground for...
  2. Replies
    22
    Views
    348

    LoL. Your an expert at it now!

    LoL. Your an expert at it now!
  3. Replies
    22
    Views
    348

    You got it!:thumbup:

    You got it!:thumbup:
  4. Replies
    22
    Views
    348

    I don't know what you mean about shaft move up...

    I don't know what you mean about shaft move up and down and has play. If you grab the input shaft itself (the shaft that goes into the transmission, not cush-drive parts) it should have a minor...
  5. Are you powering on the servo (radio) and...

    Are you powering on the servo (radio) and centering the trim before installing the servo horn? That's what you should be doing. If you don't center your radio trims and power on the servo before...
  6. Replies
    22
    Views
    348

    You have the metal star piece backwards. Flip it...

    You have the metal star piece backwards. Flip it around, then pull it up into the groove. Then it should look like this. Then install rubber cushion, washer, then the outer half w/3 screws.
    ...
  7. Replies
    4
    Views
    68

    A cracked bulkhead can cause stripped diff gears....

    A cracked bulkhead can cause stripped diff gears. A crack allows the parts (bearings,gears) to flex/move because the rigidness that holds them is compromised. I don't use a set number of shims. Each...
  8. Replies
    5
    Views
    70

    That's how my luck goes also. The glow plug...

    That's how my luck goes also. The glow plug leaking was probably the copper washer (gasket). I've had them deform after being tightened/loosened too many times.

    Maybe check the fuel tank cap is...
  9. Replies
    22
    Views
    348

    I would replace what's broken. The mesh doesn't...

    I would replace what's broken. The mesh doesn't look bad, but that spur gear assembly sliding back and forth is not good. It shouldn't be sliding on the input shaft.
  10. v1 vs v2 info: The v2 has a center diff in it...

    v1 vs v2 info: The v2 has a center diff in it along with metal gears.
  11. Replies
    4
    Views
    68

    The correct way to shim a diff is (by trying and...

    The correct way to shim a diff is (by trying and checking) to remove excess play and not by a predetermined amount of shims. To make it easy put one shim on the ring gear side and see how much play...
  12. Replies
    22
    Views
    348

    I'm going to agree with Live2Fish88 about...

    I'm going to agree with Live2Fish88 about something not right with the cushdrive/spur gear. The spur gear should be out farther (more room between it and blue plate). Check the cross pin is in the...
  13. Replies
    5
    Views
    70

    It's certainly possible. The fuel pickup in the...

    It's certainly possible. The fuel pickup in the tank could have a leak. Do you notice air bubbles in the fuel line when it starts acting up? That would be an indicator. Also check your exhaust for...
  14. Replies
    13
    Views
    252

    It's better to have more available power than not...

    It's better to have more available power than not enough. The ESC and motor will only draw what amps they need from the battery, the battery doesn't push the amp current. Stressing a battery as...
  15. It's not a direct swap. The v2.0 input shaft is...

    It's not a direct swap. The v2.0 input shaft is 6mm where the v1 is 5mm.
  16. Thank you. :thumbup:

    Thank you. :thumbup:
  17. Thread: Dust boots

    by grizzly03
    Replies
    33
    Views
    658

    https://uc5428744230b26bbc92871d1fd0.previews.drop...

    https://uc5428744230b26bbc92871d1fd0.previews.dropboxusercontent.com/p/thumb/AA1WeobZE-B4qoArK-4YHwLbldBs_psy183R4fh-MaFHLEOgqDIBj4Dj-3flx9d0eXdqyN8xnNwmukIgIoslSKFXJjpKW5dBiYb30Fm5lHc4QR6bDMvgsmb_Znl...
  18. I found the same problem with mine. Unfortunately...

    I found the same problem with mine. Unfortunately the new plate is also bent slightly. I think it has to do with the stamping process. I adjusted mine by using gear backlash as a guide to set the...
  19. Thread: Trx4 ifs?

    by grizzly03
    Replies
    17
    Views
    271

    This is what I was talking about, Dana 44 TTB. It...

    This is what I was talking about, Dana 44 TTB. It was 4WD and coil spring suspension. Ford 1980-1996. Basically had a universal joint off one side of the differential.
    ...
  20. The steering servo placement and the receiver box...

    The steering servo placement and the receiver box wire opening direction on the TRX4 really don't help at all. You really need a long lead on any servo you choose. I turned my receiver box around for...
  21. Best comment I've read in a long time! :thumbup:

    Best comment I've read in a long time! :thumbup:
  22. Flux, Have you tested out TSM with that servo? I...

    Flux, Have you tested out TSM with that servo? I might end up with that servo instead of getting another DS470BLHV.
  23. Highly impressed. Feels and works like a quality...

    Highly impressed. Feels and works like a quality piece. When they start making them again I'm getting another for my Erevo 2.0

    They only negative I can say, is I needed a servo extension wire to...
  24. Thread: XO-1 motor

    by grizzly03
    Replies
    8
    Views
    159

    I know right! Capable of 8s and a sensored system.

    I know right! Capable of 8s and a sensored system.
  25. Replies
    7
    Views
    293

    If I had an UDR I wouldn't worry about the T8...

    If I had an UDR I wouldn't worry about the T8 Truggy motors. I have a T8 1700kv i'm going to be putting in my Erevo 2.0. I also think it's better than the stock 2200kv motor. (same motor that's in...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4