Search:

Type: Posts; User: E-Power

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    3
    Views
    465

    I did one as Herbie a few years ago. Plenty of...

    I did one as Herbie a few years ago. Plenty of Herbie decals on Ebay.
  2. Replies
    14
    Views
    1,194

    By either using the Castle link or card, you can...

    By either using the Castle link or card, you can adjust many parameters including braking. I have the card and like it because it is easy to use in the field and also can be used to interface with...
  3. Replies
    2
    Views
    330

    The old connectors will work with the new style. ...

    The old connectors will work with the new style. The ID connector integrated the balance wires into the plug and should be charged on ID chargers. If charging an older plug style Lipo on an ID...
  4. Replies
    7
    Views
    1,114

    Yes, that's how you do it. Also recommend...

    Yes, that's how you do it. Also recommend trimming about 1/16 inch from the lower front wheel well for better clearance.
  5. Replies
    7
    Views
    1,114

    I run 35W on all four corners with green springs...

    I run 35W on all four corners with green springs front, black rear. This seems to be the best for general running.
  6. Thread: racing rims

    by E-Power
    Replies
    26
    Views
    799

    There are a lot better tires out there than the...

    There are a lot better tires out there than the Khumos for racing. The rims are secondary - and check the rules at your track as many have the SCT class limited to open wheel patterns, not closed...
  7. Replies
    14
    Views
    1,194

    I've run a 21/86 on my Pro-2 with heat readings...

    I've run a 21/86 on my Pro-2 with heat readings in the 150s on 2S. I normally run a 19/86.
  8. Replies
    14
    Views
    1,194

    Just bought the new ESC/3800 combo but haven't...

    Just bought the new ESC/3800 combo but haven't installed it yet (and weather isn't cooperating anyway!). It'll be interesting to see as I'm replacing the SCT/3800 combo. Good review on Squid.
  9. Replies
    10
    Views
    699

    Highly recommend using the STRC hinge pin set...

    Highly recommend using the STRC hinge pin set (work with RPM arms) as they are stronger and they have lock nuts so they don't back out.
  10. Replies
    16
    Views
    987

    You can buy just the kit with the set screws and...

    You can buy just the kit with the set screws and the loc caps - clip off the nub on your stock body mounts, drill a hole and insert the ProLine set screws. Did this on two Rustlers as they don't...
  11. Replies
    14
    Views
    479

    MIP for hex drivers and just ordered a set of...

    MIP for hex drivers and just ordered a set of their new nut drivers - best quality I've run across.
  12. Replies
    11
    Views
    1,721

    I find the Tamiya nozzles to be the best...

    I find the Tamiya nozzles to be the best performing overall. Seem to be more consistent in spray, with no "spitting".
  13. Replies
    4
    Views
    540

    The holeshots work fine on the front also. On...

    The holeshots work fine on the front also. On hard clay I prefer the clay compound electrons on all four corners.
  14. Replies
    10
    Views
    749

    Another option is the new sensored motors (3800...

    Another option is the new sensored motors (3800 and others) with the new Mamba X ESC. They are showing up in stores now. These look very promising with the sensored start up to eliminate cogging...
  15. Replies
    7
    Views
    381

    The CA glue can affect the plastic. I'd...

    The CA glue can affect the plastic. I'd recommend a dab of silicon caulk or a larger screw as noted above.
  16. Replies
    6
    Views
    378

    The Proline Primes in the clay formula are also...

    The Proline Primes in the clay formula are also quite nice on the street. They have more grip than the Street Fighters, but will wear a bit faster.
  17. Replies
    2
    Views
    252

    Yes, the kv is 3500. However, kv ratings are not...

    Yes, the kv is 3500. However, kv ratings are not consistent across companies. It is best to look at each company's recommendation. For general driving (bashing, etc.), somehwere between 3400 and...
  18. You can get the body a little lower by using the...

    You can get the body a little lower by using the ProLine body mounts. However, due to the low chassis, the body will sit above it.
  19. I prefer the Xacto knife, but use lexan scissors...

    I prefer the Xacto knife, but use lexan scissors for clean up sometimes. Also recommend the ProLine sanding block.
  20. Thread: GTR Shocks

    by E-Power
    Replies
    6
    Views
    367

    In place of the stock shoulder screws that are...

    In place of the stock shoulder screws that are used with the Ultras, you need 3x15 button head screws (Traxxas 2579). Also, on the front you'll need to swap out the lower ball with the stock version...
  21. Replies
    17
    Views
    1,249

    Another vote for MIP tools and they now have nut...

    Another vote for MIP tools and they now have nut drivers! For the most secure body attachment, I prefer the ProLine SecureLoc caps. You can either change out to the ProLine mounts with SecureLoc or...
  22. Replies
    18
    Views
    537

    Are you sure the wheel nut is cinched down? That...

    Are you sure the wheel nut is cinched down? That the wheel is set properly on the hex?
  23. Thread: Best Upgrades

    by E-Power
    Replies
    9
    Views
    2,766

    Agree with the aluminum - I like the bulkhead and...

    Agree with the aluminum - I like the bulkhead and steering blocks in aluminum (STRC is a good brand) and the STRC hinge pin set with lock nuts so they never back out.
  24. Replies
    20
    Views
    1,355

    Normally the charger will show 4.2v per cell when...

    Normally the charger will show 4.2v per cell when fully charged, and the LVD is set at 3.5v per cell for the warning (I believe they stop at 3.4v).
  25. They are the same - only difference is the wheel...

    They are the same - only difference is the wheel finish: chrome for XL5, black chrome for VXL
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4