Search:

Type: Posts; User: zedorda

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    10
    Views
    313

    It looks like the mesh is too tight but a picture...

    It looks like the mesh is too tight but a picture doesn't fully communicate the mesh feel. Even with a piece of paper in there you can set the mesh too tight. I see alot of people say to set your...
  2. With the addition of (properly) I am guessing you...

    With the addition of (properly) I am guessing you didn't just add more glue and pushed the tire back in place. You must of removed all the original glue and fully cleaned and denatured the rubber and...
  3. Replies
    3
    Views
    99

    The pinions should be able to swap without issue....

    The pinions should be able to swap without issue. No need to change anything but the motors. Keep the 4x4 with its original pinion and let the 2wd keep its original pinion.

    The Slash 4x4 VXL has...
  4. Replies
    6
    Views
    96

    If you stray more than 30+/- it is highly...

    If you stray more than 30+/- it is highly suggested to change spring rates accordingly. Stiffer for thicker and softer for thinner. If the dampening is not in sync with the spring rate results become...
  5. Replies
    7
    Views
    241

    Reinforcing or supporting the body has 2...

    Reinforcing or supporting the body has 2 compromises to consider, cost and weight. Weight reduces efficiency of the rig fast. Cost can defeat the purpose from the start. Brute force bodies and the...
  6. Replies
    12
    Views
    323

    The VXL-3m will not likely power a 540 can with...

    The VXL-3m will not likely power a 540 can with sufficient amps. Seems like a good way to get some magic smoke.
  7. Replies
    20
    Views
    710

    Yes thank you all this does help.

    Yes thank you all this does help.
  8. Replies
    2
    Views
    193

    If you need clearance for any reason this is...

    If you need clearance for any reason this is about the smallest one.
    ...
  9. Thread: Tool Kit

    by zedorda
    Replies
    16
    Views
    439

    Actually you might want to check that. Because...

    Actually you might want to check that. Because you can have the same torque at different speeds. Speed and torque have no synchronized correlation.
  10. Replies
    20
    Views
    710

    Don't the Sledgehammer wheels have Traxxas 17mm...

    Don't the Sledgehammer wheels have Traxxas 17mm splined hexes? I have standard 17mm HR adaptors.
  11. Thread: Tool Kit

    by zedorda
    Replies
    16
    Views
    439

    I actually started using my power screwdriver...

    I actually started using my power screwdriver because I have a bad habit of over tightening fasteners. This power screwdriver has saved me a lot of headache and taught me just how little you have to...
  12. Thread: Snap-on Rally?

    by zedorda
    Replies
    4
    Views
    566

    I have seen Slash Snap-on trucks but never a...

    I have seen Slash Snap-on trucks but never a Rally but it doesn't surprise me. Snap-on does this kind of stuff often.
  13. Replies
    10
    Views
    295

    If it just to get a max speed for a speed run and...

    If it just to get a max speed for a speed run and not a long bash session. You can try just getting a small 2s battery. The weight saving can be dramatic.
  14. Thread: Tool Kit

    by zedorda
    Replies
    16
    Views
    439

    I have the Black+Decker LI4000 power screwdriver....

    I have the Black+Decker LI4000 power screwdriver. It has the torque limiter and lithium power. I found it at a local Lowes or Home Depot not sure which now. But here is a amazon link as an example.
    ...
  15. Replies
    23
    Views
    457

    A center diff will help but the monster truck...

    A center diff will help but the monster truck tires will still kill your cornering.
  16. I think it was an STRC kit but it was a long time...

    I think it was an STRC kit but it was a long time ago so not sure at all. But it was a kit I just upgraded the bar.
  17. Replies
    20
    Views
    710

    I already have 17mm hexes, MiP X-Duty axles,...

    I already have 17mm hexes, MiP X-Duty axles, hardened steel spiral cut diff gears with LEM diff cups, Tekno RC Big bone center shaft, full metal center diff, larger bearing metal motor mount, and all...
  18. Replies
    14
    Views
    462

    Flex-Seal Clear spray and strategic use of...

    Flex-Seal Clear spray and strategic use of drywall tape.
  19. Replies
    20
    Views
    710

    I don't really do high speed with the Monster...

    I don't really do high speed with the Monster Slash but I do worry about tearing from just plain high torque once in a while. Thanks.
  20. That is a great simple mod to firm up the...

    That is a great simple mod to firm up the front-end. I made my own upgrade bar for my sway bar setup. I used piano wire. Which is hardened stainless spring steel. It made a huge difference. I...
  21. Replies
    20
    Views
    710

    Thanks for the replies. I was hoping for use...

    Thanks for the replies. I was hoping for use experience like ballooning and wear rates. Also which model fits the Slash since I can't find the details of the differences between the models. Still...
  22. Thanks for the clarification, it just made me...

    Thanks for the clarification, it just made me wonder. :)
  23. Replies
    10
    Views
    359

    These are the best body clips I have ever used....

    These are the best body clips I have ever used. If you don't want to switch to the screw cap type body post I can't suggest these more.

    https://www.vgracing.com/product/Body_Clips_8.html

    I...
  24. Replies
    15
    Views
    281

    Sorry just had to get that confirmed. Thanks :)

    Sorry just had to get that confirmed. Thanks :)
  25. Replies
    15
    Views
    281

    I have not seen the shocks you actually have but...

    I have not seen the shocks you actually have but I have to ask. Are the rear shocks longer than the front shocks?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4