Search:

Type: Posts; User: Greatscott

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    24
    Views
    2,083

    Progress!!!! I finally got some hardcore time...

    Progress!!!!

    I finally got some hardcore time to work on the cab base, and its chassis interface. I printed a test piece in white filament (5% infill) to allow for easy marking for changes and...
  2. Replies
    3
    Views
    71

    Sounds like a gear alignment issue. Make sure...

    Sounds like a gear alignment issue. Make sure your shift servo is actually shifting your transmission into low.
  3. Replies
    147
    Views
    20,800

    Found this video from Uncle Jessy, anyone else...

    Found this video from Uncle Jessy, anyone else use printing resin to smooth and strengthen FDM prints?


    <iframe width="560" height="315" src="https://www.youtube.com/embed/lcQKHOWmG44"...
  4. Replies
    8
    Views
    236

    Overall the TRX4 is very stout, its failure...

    Overall the TRX4 is very stout, its failure points will depend on how you are running it.

    For just trail running and light crawling, everything should hold up fairly well. If you get into more...
  5. Replies
    4
    Views
    114

    Depends... The least expensive option is to...

    Depends...

    The least expensive option is to wire them up yourself, if you can solder, it is fairly easy to do.
  6. Replies
    9
    Views
    237

    WELCOME TO THE FORUMS!!! Lets start...

    WELCOME TO THE FORUMS!!!



    Lets start here...

    Were you unplugging and unplugging things on the receiver (RX)? If so, check and make sure the steering servo is plugged into one of the first...
  7. Replies
    6
    Views
    210

    Swap your steering servo and your ESC on the RX....

    Swap your steering servo and your ESC on the RX. If the servo works through the throttle then your problem is in the ESC or motor.
  8. Replies
    12
    Views
    506

    Here are the mods... The truck comes with...

    Here are the mods...

    The truck comes with working fog lights, but the grill and lights on the body are just a sticker. I designed and printed the grill and headlight bezels, and the roll bar.
    ...
  9. Thread: Gearing

    by Greatscott
    Replies
    7
    Views
    186

    Take a look at your Castle documentation, it...

    Take a look at your Castle documentation, it gives a chart for what is appropriate for you RC based on model and weight.

    "Normal" basher gearing is around 16/90, which give a RR of 5.6:1, where...
  10. Replies
    12
    Views
    506

    I have a 1:24 Element, its a fun little truck. I...

    I have a 1:24 Element, its a fun little truck. I have done a few mods, made a front grill with lights, roll bar, and an electronics tray. I have also upgraded the ESC and RX. I don't see any reason...
  11. Thread: Rc rv

    by Greatscott
    Replies
    66
    Views
    1,836

    WOW, you turned that project out quickly!!!! That...

    WOW, you turned that project out quickly!!!! That thing looks sharp, very nice work!!!
  12. Thread: Gearing

    by Greatscott
    Replies
    7
    Views
    186

    If you are going for pure speed, and not...

    If you are going for pure speed, and not acceleration, 31/76 will get you there. If you are not going for speed, and just looking at bashing, this gearing will be horrible. No matter what, you REALLY...
  13. Replies
    11
    Views
    280

    Given that most forums like this are drying up...

    Given that most forums like this are drying up and blowing away, I seriously doubt that; most likely you are talking about FB. But, you have to go where the windows blow you.
  14. Replies
    7
    Views
    130

    Traxxas has only really give an "ish" for what...

    Traxxas has only really give an "ish" for what its LVC is; and, as stated, is not adjustable. For people performing tests, the best guess was 3.4VDC, which is a bit on the conservative side, but...
  15. Replies
    28
    Views
    811

    What voltage is the Fusionís BEC set for? ...

    What voltage is the Fusionís BEC set for?


    Sent from my iPhone using Tapatalk
  16. Replies
    4
    Views
    167

    You want marine heat shrink.

    You want marine heat shrink.
  17. Replies
    11
    Views
    280

    No, the Traxxas site does not host pictures. You...

    No, the Traxxas site does not host pictures. You have to use a 3rd party hosting site like Flickr or Tapatalk.
  18. Replies
    4
    Views
    256

    The best upgrade you can do for racing is simple,...

    The best upgrade you can do for racing is simple, get as much track time as you can!

    When you first hit the track it will be a bit frustrating, its technical and a lot different than bashing, and...
  19. Replies
    11
    Views
    255

    WELCOME TO THE FORUMS!!!! Do you have pictures...

    WELCOME TO THE FORUMS!!!!

    Do you have pictures of your TRX4?
  20. Thread: Rc rv

    by Greatscott
    Replies
    66
    Views
    1,836

    THAT'S AWESOME!!! Looking forward to seeing some...

    THAT'S AWESOME!!! Looking forward to seeing some video of it running!!!

    Seriously not that direction I would have gone with it, but that is one the of things that makes this hobby awesome.
  21. Replies
    20
    Views
    583

    If you want something slow and can take a...

    If you want something slow and can take a beating, go with a TRX4. Drop a 45T motor in it and lock it in low gear (if it is a 2-speed model). A 2S 5000mha pack will allow him to creep around for...
  22. I'd print it with PLA or PETG at 100% infill....

    I'd print it with PLA or PETG at 100% infill. Also, I'd print it as it is orientated in Thingiverse, that will give the most strength.

    The only issue that might arise is UV deterioration caused...
  23. Replies
    4
    Views
    174

    I have tried going the other way, and the Android...

    I have tried going the other way, and the Android didn't make much sense to me, so I stuck with iOS.

    My wife's aunt (75 y/o) has made the switch from Android to iOS, and found iOS a lot easier to...
  24. Replies
    8
    Views
    450

    Banggood is hit or miss. I have always gotten...

    Banggood is hit or miss. I have always gotten what I paid for, and, more or less, have been satisfied with the quality for the price paid. But, their shipping is iffy at best. I have order parts and...
  25. Tighten down your slipper clutch,l. Drop a couple...

    Tighten down your slipper clutch,l. Drop a couple of teeth on the pinion. Goto 3S.


    Sent from my iPhone using Tapatalk
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4