Search:

Type: Posts; User: dronenewbie

Page 1 of 12 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    293

    [emoji106] Sent from my iPhone using...

    [emoji106]


    Sent from my iPhone using Tapatalk
  2. Replies
    5
    Views
    251

    I spray accelerator on it, hardens right away....

    I spray accelerator on it, hardens right away. Make sure to only use it outdoors though, that stuff is really bad when inhaled.


    Sent from my iPhone using Tapatalk
  3. I like tinkering on my rc’s almost more than...

    I like tinkering on my rc’s almost more than running them...[emoji51]
    Seriously though, it doesn’t really matter what type of rc you get, they all will need the same kind of maintenance sooner or...
  4. Replies
    16
    Views
    595

    I never had an issue with the Traxxas aluminum...

    I never had an issue with the Traxxas aluminum wrenches. Make sure you only use them for their intended purpose: adjustment of the steering and toe rods. If you want something else, most hardware...
  5. Replies
    7
    Views
    323

    Yeah, like others said. Chassis slap is pretty...

    Yeah, like others said. Chassis slap is pretty normal. Matter of fact if you go to a race track, even high end race buggies and truggies do it. If you stiffen it up to the point where this does not...
  6. Replies
    3
    Views
    293

    This is what works best for me: Center diff oil....

    This is what works best for me:
    Center diff oil. I changed mine to 500.000. Less wheely happy, more front traction. Downside is, when accelerating really hard in a straight line, front tires will...
  7. Secure the wheelie bar with a zip tie and you’re...

    Secure the wheelie bar with a zip tie and you’re all set.


    Sent from my iPhone using Tapatalk
  8. Replies
    4
    Views
    207

    I always use diff shims to remove all of the...

    I always use diff shims to remove all of the excessive play in my drivetrain. Remove cup, place a shim on output shaft, put cup back, slide locking pin back in and check. I shim mine where there is...
  9. Looks like the motor-plate is bent forward....

    Looks like the motor-plate is bent forward. Remove it and place it on a flat surface to verify. Either bend it back, or replace it with a new one.


    Sent from my iPhone using Tapatalk
  10. Thread: Dust boots

    by dronenewbie
    Replies
    36
    Views
    1,476

    I ordered them in black, curious to see how...

    I ordered them in black, curious to see how they’ll hold up.


    Sent from my iPhone using Tapatalk
  11. Replies
    35
    Views
    988

    It turns way better imo. Plus to make it match...

    It turns way better imo. Plus to make it match the other side. Might be a little sketchy going straight, but turns less like a boat. It depends on what you want to do I guess. I set mine up for track...
  12. Broke steering arm and a few other issues

    Yeah, that’s what I actually meant.... can’t edit my comment for some reason...
    Those STRC arms is what I have. Totally forgot the brandname....was asked about it by someone else. [emoji482]

    ...
  13. Replies
    35
    Views
    988

    Hard to tell by looking at pictures, but your...

    Hard to tell by looking at pictures, but your front right (passenger side) looks like it could use just a tiny little bit more toe out. Rest looks good. Drive it first though, make adjustments as...
  14. Replies
    35
    Views
    988

    Looking good! Sent from my iPhone using...

    Looking good!


    Sent from my iPhone using Tapatalk
  15. Replies
    35
    Views
    988

    No, just use the wrench that came in the box on...

    No, just use the wrench that came in the box on the hex center part of the toe link. If you installed them correctly, forward should increase toe in, backwards should give you more toe out.


    Sent...
  16. Replies
    35
    Views
    988

    I just followed the Traxxas instructions that...

    I just followed the Traxxas instructions that came with the toe-links. They actually tell you the length for both, front and rear. [emoji106]


    Sent from my iPhone using Tapatalk
  17. I wouldn’t replace the whole bell crank to alloy....

    I wouldn’t replace the whole bell crank to alloy. Just both servo arms. The one you broke, and on the servo itself. Did you upgrade the servo saver spring yet? If not, that’s what probably caused the...
  18. Replies
    35
    Views
    988

    Pretty normal looking if you ask me. A few...

    Pretty normal looking if you ask me. A few degrees toe’d in, in the rear - a few degrees toe’d out, in the front. Looks like stock set up actually.


    Sent from my iPhone using Tapatalk
  19. Replies
    35
    Views
    1,603

    I also like how the ERevo handles with 8th scale...

    I also like how the ERevo handles with 8th scale sized tires and wheels. I have some 1/8 Truggy wheels, and those tires are really firm to allow the suspension do it's job instead of the tires. More...
  20. Replies
    4
    Views
    172

    I threaded mine in, just like my “old” ones...

    I threaded mine in, just like my “old” ones looked, so they’re all the same length.


    Sent from my iPhone using Tapatalk
  21. Replies
    13
    Views
    369

    They not only look better, but they’re so beefy...

    They not only look better, but they’re so beefy you know it’ll take a lot to break them.


    Sent from my iPhone using Tapatalk
  22. Replies
    12
    Views
    756

    Remove the motor and check for any binding in the...

    Remove the motor and check for any binding in the driveline. All moving parts should spin freely. Double check all screws. Ready to run models are notorious for having a lot of screws not properly...
  23. Replies
    3
    Views
    203

    I 2nd that. I put a castle MM2 in mine as well!...

    I 2nd that. I put a castle MM2 in mine as well! [emoji482]


    Sent from my iPhone using Tapatalk
  24. Replies
    9
    Views
    301

    Readingthiswithoutpunctuationsreallymademyheadhurt...

    Readingthiswithoutpunctuationsreallymademyheadhurt. [emoji23][emoji1787][emoji23]


    Sent from my iPhone using Tapatalk
  25. Replies
    49
    Views
    1,054

    ^^ that’s what I use. Can’t go wrong with that! ...

    ^^ that’s what I use. Can’t go wrong with that!


    Sent from my iPhone using Tapatalk
Results 1 to 25 of 276
Page 1 of 12 1 2 3 4