Search:

I got a pretty darn-sweet mavic clone drone from banggood (or gearbest)? Dont remember. But also have gotten wheels, tires, axles for Rustler 4x4, a video doorbell for home, and several other things....

So much bad-to-the-bone!, I cant even!

Sent from my Pixel 3a using Tapatalk

I can run almost or in excess of 70mph up and down my street on 4s, for the entirety of two, 2s, 5200mah 50c batteries by Zeee....check temps (after nothing but wide open passes roughly 1/4 mi. Maybe...

Youll be absolutely LUCKY, to hit 58! Just saying! And for the amount of HEAT the vxl produces on STOCK gearing?! Shoot!....
I love my HW power system on 2200kv and anywhere from 15t pinion (for big...

One more thing I noticed was a little pegs that are used to align the ring gear onto the diff cup, are very fragile and can break off the slightest stress / misalignment etc.

Just a few minutes...

Well when you look at the assembly instructions / diagram there's definitely a shim on only one side for our particular vehicle I suggest putting a shim on both output drive gears in order to bring...

The regular teflon coated washers dont fit over the gear shafts, only stub axles, etc. So it MUST be a "diff shim" idk if traxxas sells em without having to buy gearset??

Look around on floor or...

The gear set should gave at least one shim, they blend right-in with the metal color of output gears. I had overlooked em my first diff rebuild because they actually stuck SO flat against the gear
...

Dont forget that one side gets a shim AND BLUE RING, i put both, on both outputs. This bring the spider in-closer-together

Sent from my Pixel 3a using Tapatalk

Did putting the wrong screw in wrong hole cause a piece of plastic to bend inwards and is still holding the diff somehow???

Otherwise, grab a flashlight and try to look at the front...

O.g. diff. Output bearings?? Or brand new/cleaned/lubed? Those bearings take a BEATING on these trucks.

Sent from my Pixel 3a using Tapatalk

Otherwise, i HAVE had an instance where the spiders didnt all-4 mesh properly during assembly, so when i cranked down the ring gear bolts, it was like a spool, instead of a differential.

Sent from...

Yes, noted in assembly instructions... The I-bar has two flat corners, and two rounded corners, the rounded ones need to go down (into diff cup), the cup side spider (which stick out to attach axles...

2x. 6882x
1x 6879R (rear spiral cut gears)
1x 5379R (front". ")
And i recommend not going too too high with the diff fluid viscosity, I tried 2 million weight and the...

That kit is a must in both my gifts as I'm now running 4s and a 2200 KV system with slipper eliminator

Sent from my Pixel 3a using Tapatalk

One 6882 x, per axle. So two sets, BUT, u might look out once you open the diff housings and find out that the gears are in good shape what I realized is that once that slop develops, the screws that...

Dont forget the spider gear set WITH "I-bar" support!

Sent from my Pixel 3a using Tapatalk

Thank you for mentioning this little factoid, it's been so long since I used the original TX/RX, that I forgot all about TSM. Lol!
But you're exactly right if it's not tire specific-"wobble", then...

While I agree with you, I personally swamped to an aluminum bill crank/steering setup with bearings instead of bushings, and within a week tops, still got some slop

Sent from my Pixel 3a using...

No exactly sure if u mean it like a wheel/tire issue?? (Tires not glued on straight, bad wheel bearings, loose pivot balls, wallowed out plastic driveshaft-u-joint-holes,) are all things that come to...

If you mean by the way it bends down in the front, I get it but, most people don't see, that I have less than 2 in of free space in front of my new receiver box location unless you were talking to...

I run max8 and 2200kv HW motor in my R4sty, and absolutely L.O.V.E. the setup! Sure it wont dissappoint for NPDR!!

Sent from my Pixel 3a using Tapatalk

Recently acquired for my R4sty, a set of Long GTR's (front). And i absolutely love them!! They are sweet, especially since adding the Variable Dampening Kit to em! (My rusty is heavy af due to 1/8th...

I believe someone around these forums told me that you can use "spacers" to mount the brace, i took it as, maybe using the two holes which a swaybar would screw into on your chassis, add the tall,...

Anyone tried the Revo springs on the R4sty?

Sent from my Pixel 3a using Tapatalk