Search:

Yeah, I have one in my savage flux with the castle 2200kv 4074 sensored in it. I think I drove that truck twice last year... lol!

I prefer plastic when they hold up. The one in my ERBEv2 has been in it for over a year without any issues. All on 6S power and a lot of jumping.

What motor is that? Is that a Mamba Monster X or Mamb X esc?

One nice thing about mine is that when you move the pushrod to a different hole, nothing has to change with the length of the cable and it still does it's job. So if you run smaller tires and want to...

It's a direct replacement. I have the older lighter duty version in mine, didn't know about 6780 at the time.

The older one needs an aftermarket alloy cup as it gets deformed on 3S and allows the...

Yeah, makes them look like they fit the truck better. If I didn't have that, I'd likely try the hoss tires, just wish they had a set on 17mm. If the maxx4s tires were further offset, those would work...

V2 Vids did that with his xmaxx too:

https://www.youtube.com/watch?v=SH5hLnrGnYI

I think Kevin Talbot did that as well.

Makes for an amusing video. lol!

The hard anno inside the shock I believe is also teflon coated so it's smoother when the piston contacts the sides a bit. Also, the TiNi coating on the shock shafts makes the surface harder so they...

I had the non-belted 2.8 trenchers when I ran 2S and 3S. They were decent, but did spin a lot in the grass. Not nearly like the slicks that come on the stampede 4x4 vxl (2.8 talons). Those were...

I run the GTR's on my stampede 4x4, which is the same as the hoss regarding suspension. They hold up really well.

I use the following on mine:
Associated 70wt front rear
VG Springs/GTR Shocks...

I'd agree, but if he already has the steel cvd's, it would be a bit more cost effective to use 1/2" offset adapters.

If not, then the wide kit is likely the better solution.

At 10mm+, I'd go with the wide arms instead. If just 10mm is all your looking for, it won't add a lot of strain.

I ran hot racing 10mm on my stampede 4x4 just to make it a bit more stable, wider...

A jato is nothing like any of those. :)

It's a handful at speed, but gets there a lot easier than a single speed 2wd stadium like the RC10GT or XXX-NT or nitro rustler.

I usually ran mine...

I don't know... I know I used new screws with mine, but I have a lot of various lengths on hand. So I used the longest I could I think. That's what I usually do with diffs. Especially when they are...

After a nasty crash with my slampede:
https://www.dropbox.com/s/imdhcsh2armnawd/2020-1107-stampede-brokenGPM-SLA019A%26HRAxleCarrier.jpg?raw=1

Living in a 2 bdrm apartment has it's challenges... carrying everything down 3 flights of stairs is one, storage is another. My office is my RC room, so half the room is RC stuff.
...

Seeing them side by side is really nice. I didn't think the LP's would be that much larger.

From what I've read, when you have really high quality packs, they tend to be better matched cells (similar IR) that discharge at a similar rate, so balancing isn't as big of a deal on them all the...

Really though, the 3.3 would be plenty for a truck the size/scale of the hoss. Throw in an e-revo 2 speed and get to it!

For me, the 3.3 wasn't enough for the revo. It was too long/heavy for my...

I've run the following on my BLX185:
Hobbystar 3665 3100kv
Arrma 4074 2050kv BLX2050
Traxxas/Castle 4074 2200kv from ERBEv1
hpi tork 2200kv

The HPI tork is running off it currently.

You...

It's the tooth size/pitch on the spur/pinion. The larger the number, the larger the tooth.

All I have are Mod .8, 32P and Mod 1. My eJato and stampede run M.8/32P, the rest use M1.

I think M.8...

Just avoid landing on power and you should be ok until you get the other diff upgraded.

As far as I know, the upgraded ring/pinions are just machined and helical cut to make them stronger with the same gear ratio.

The outdrives come with the diff internals that use the i-bar like the...

The parts I listed would work for both the front and rear diffs on a stampede/slash with the stock axle sliders or the MIP X-Duty versions (I have those).

The mistake I made was ordering this:...

In a slash, on 3S, they should hold up fine really, but best to get the i-bar/spiders with proper output shafts and hd cups. I made the mistake and got the wrong outdrives for mine.

I run my on 4S...