Search:

Type: Posts; User: BashedNotBeat

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    12
    Views
    404

    maybe it is a loose motor wire? or hopefully...

    maybe it is a loose motor wire? or hopefully someone with more knowledge of failed brushed motors will chime in here and have some valuable input.
  2. Replies
    11
    Views
    488

    all I have seen a photo of the issue and it is...

    all I have seen a photo of the issue and it is 100% an issue with getting the 2 axle shafts to fit together all the way it seems from the photo to be jammed halfway in. I assume it is from the axles...
  3. Replies
    11
    Views
    488

    sent a PM to your email

    sent a PM to your email
  4. Replies
    12
    Views
    404

    my slash titan motors have never had an issue...

    my slash titan motors have never had an issue from water. every month or so I remove to motor and oil the shaft bushings but it has never not turned from water. it is possible you have a bad motor...
  5. Replies
    11
    Views
    737

    haha I hate how people are so brand loyal. at the...

    haha I hate how people are so brand loyal. at the end of the day its just toys we buy to have some fun with. who cares who makes them as long as they are good products. I have no loyalty to traxxas...
  6. Thread: Yay

    by BashedNotBeat
    Replies
    12
    Views
    811

    so far only thing my maxx has broken is the rims....

    so far only thing my maxx has broken is the rims. im still using the wheels until they simply wont work anymore. I think its bulletproof out the box and I jump mine hard. I have seen my rear wheel...
  7. Replies
    6
    Views
    333

    maxx really is a game changer it does not handle...

    maxx really is a game changer it does not handle great out of the box but it wasn't supposed to its a monster truck but it can be moded to handle super well. what the maxx is great for is a lot of...
  8. Replies
    11
    Views
    488

    are you saying the threaded axle shaft is not...

    are you saying the threaded axle shaft is not sticking out far enough to get the wheel nut on?
    if this is the case you make have not set the wheel hex onto the pin in the axle. try to remove the...
  9. Replies
    11
    Views
    737

    It would be nice if we could just upload here...

    It would be nice if we could just upload here directly
  10. Replies
    11
    Views
    737

    If I knew how to post photos I can. I’m not...

    If I knew how to post photos I can. I’m not really a fan of using 3rd party’s to post photos online.
  11. Very easy to do center diff just need to remove...

    Very easy to do center diff just need to remove Center driveshaft cover and front and rear bulk heads and all 3 diffs come right out. I did all 3 of mine in 1 hour and then let them sit for 3 hours...
  12. Replies
    5
    Views
    361

    Yes it was very easy to use the pin setup. And...

    Yes it was very easy to use the pin setup. And yes boosts I agree I loved the insane speed but 9/10 times I didn’t need it just ended up slamming on the brakes. Now I use the extra torque to drift my...
  13. Replies
    5
    Views
    361

    MAXX - gearing changes.

    thought I would start this one off with what I have noticed in my gearing change and see if others want to post up about what they have found with their changes.

    Stock gearing 24/50

    my current...
  14. Replies
    3
    Views
    292

    Had this issue with mine new. What fixed it for...

    Had this issue with mine new. What fixed it for me was recalibrate the radio to the esc. After that my cogging was much better. I also geared down to a 22t pinion and that helped even further
  15. Replies
    11
    Views
    737

    it comes stock with voltage amps rpm speed...

    it comes stock with voltage amps rpm speed incline angle and temp all stock. but these are readings from the esc and the receiver. you would need the sensors to get readings from the motor like...
  16. Replies
    3
    Views
    391

    bummer at least it stops them early rather then...

    bummer at least it stops them early rather then to late.
  17. Replies
    53
    Views
    3,674

    Followed the links you posted and got nothing...

    Followed the links you posted and got nothing shown on traxxas website...... maby they went down again
  18. Thread: New Maxx

    by BashedNotBeat
    Replies
    20
    Views
    1,392

    Self righting works great for me on 4 cell. I use...

    Self righting works great for me on 4 cell. I use 5000mah 4 cell lipos with 45c and some with 50c ratings and self righting has been working fine. I don’t always push the button tho. I do it myself...
  19. Replies
    3
    Views
    391

    How to set LVC on traxxas link app

    Hey all. Is it possible to adjust the voltage when my traxxas vxl4s from my Maxx truck cuts power for lvc. Stock it is set way to early on my packs and I want to lower it 0.2 volts if possible. I...
  20. Replies
    15
    Views
    507

    Rpm makes great plastic but any time it is used...

    Rpm makes great plastic but any time it is used with bearings it has a life span only so many flexes they will do before they start to get loose and should be replaced. I like plastic over aluminum...
  21. Replies
    53
    Views
    3,674

    From my LHS

    From my LHS
  22. Replies
    53
    Views
    3,674

    I have my wide kit coming in 3 weeks in orange...

    I have my wide kit coming in 3 weeks in orange for my maxx. I’ve heard good things. Only negative is it looks less like a monster truck and more like a truggy after. I just want to try it for myself...
  23. 28/86 seems to tall for 2wd unless your doing...

    28/86 seems to tall for 2wd unless your doing single speed runs and then giving it a break. Stock gearing is 19/90 I would say try 21/86 and use a 3cell LiPo and see where that gets you but yes use a...
  24. Replies
    71
    Views
    8,234

    All I can say is how was the moon MR. Maxx? ...

    All I can say is how was the moon MR. Maxx?

    SEND IT!!!!
  25. Replies
    7
    Views
    739

    it probably is but if the plastic was flexible...

    it probably is but if the plastic was flexible enough this would not be an issue. the plastic must not be able to handle the stress that the maxx chassis can put into the wheels.
Results 1 to 25 of 87
Page 1 of 4 1 2 3 4