Search:

Type: Posts; User: olds97_lss

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    1
    Views
    12

    Self righting is cool, but it tends to be hard on...

    Self righting is cool, but it tends to be hard on stuff. Usually diffs, axles and the esc moreso than anything else.

    I'm guessing your issue was a fluke though.
  2. Replies
    2
    Views
    10

    https://traxxas.com/products/parts/5394X ...

    https://traxxas.com/products/parts/5394X

    That's the one for the 3.3. It removes a bunch of stuff from the transmission, the servo/linkage and optidrive if you still have it.
  3. Replies
    20
    Views
    896

    What's the rooster? Got a link?

    What's the rooster? Got a link?
  4. Replies
    5
    Views
    62

    I run that in my stampede 4x4 vxl (mip cvd's,...

    I run that in my stampede 4x4 vxl (mip cvd's, 2.8" trenchers) on 3S and the 3660sl/3200kv motor runs hot even with a 13T pinion. Should do fine in a rustler though, less weight. I suggest getting the...
  5. Replies
    1
    Views
    45

    The center diff runs 20M silicone "oil" in it,...

    The center diff runs 20M silicone "oil" in it, it's more like a putty. I have found that if I run the truck pretty hard for a pack or two that it does seem to loosen up quite a bit, but I notice my...
  6. Thanks. The track is accessible to the public,...

    Thanks.

    The track is accessible to the public, but maintained privately. I'm guessing there were some RC'rs that weren't respectful of the property or the actual bmx people there. Considering the...
  7. Replies
    7
    Views
    101

    The e-revo is larger. More ground clearance,...

    The e-revo is larger. More ground clearance, handles rougher terrain better.

    Are the tracks you have to run at RC, BMX, MX? If they are RC, try going there on weekends when people are there to see...
  8. Replies
    22
    Views
    21,160

    Depending on what your running in the truck, you...

    Depending on what your running in the truck, you might want to look at getting an alloy cup as suggested. I run one on my 4pede on 3S with a max10 sct/3200kv 3665 motor and 2.8" trenchers. It does...
  9. 2019/10/07 - Most recent bash session and videos since my last post

    My latest ERBEv2 bash at the skate park:

    https://www.youtube.com/watch?v=tJuVyQ5jKtE

    Got booted from a bmx track that was over an hour away before I even got started. I had only been there 4 or...
  10. Replies
    10
    Views
    329

    I can't recall what I ran before with standard...

    I can't recall what I ran before with standard revo shocks or what pistons I had in it at the time. I had the hard anno'd shocks on there for a while and would just dump the oil and add...
  11. Replies
    16
    Views
    145

    Just the esc for $85 on amain:...

    Just the esc for $85 on amain:
    https://www.amainhobbies.com/hobbywing-ezrun-max10-sct-120a-waterproof-sensorless-brushless-esc-hwa30102601/p507477

    I run one in my stampede 4x4 vxl on 3S with a...
  12. I ran the SRC Terrain Crushers for a while on my...

    I ran the SRC Terrain Crushers for a while on my v1 revo. That was before I found out those are not the tires you want for jumping. I now have 3 cracked rims. :(

    What I found with those...
  13. Replies
    7
    Views
    135

    I run this in mine with hobbystar 6200mah 3S...

    I run this in mine with hobbystar 6200mah 3S packs that pretty much fill the battery bays:
    P2 rockers/rods
    70w AE VDK #3 front
    60w AE VDK #2 rear
    RCRaven Springs f/r

    I have a little bit of...
  14. Replies
    3
    Views
    95

    If I were to start over, I'd like go with the...

    If I were to start over, I'd like go with the Futaba 3pv. Enough features for most bashers. Good quality and a long range. If I needed more than 10 model memory, I'd go with the 4PM.

    As it is, I...
  15. Replies
    4
    Views
    244

    That's about how I run mine as well. If I have it...

    That's about how I run mine as well. If I have it setup so that the center of the truck is much higher, then I likely have something set too tall and end up snapping shock ends off on full...
  16. Pretty sure there was a "brushed" revo that...

    Pretty sure there was a "brushed" revo that existed with the e-revo platform first came out. The summit is still brushed, but probably has it's own forum section.
  17. For the weight of the truck, the 6S arrma system...

    For the weight of the truck, the 6S arrma system (BLX185/2050kv 4074 motor) will be severely overkill for the stampede 4x4, slash 4x4, rustler 4x4, but you likely won't have to even give heat a...
  18. I converted mine from a 1.0 to a 2.0 using a 2.0...

    I converted mine from a 1.0 to a 2.0 using a 2.0 roller. I transferred my electronics, body mounts, body, wheels and other misc upgrades that would swap.

    As far as I know, there are only 2 kinds...
  19. Replies
    38
    Views
    2,213

    The arrma guys have similar issues with the YR...

    The arrma guys have similar issues with the YR fans.

    You can find aluminum framed fans. They flex less so the blades are less likely to touch the side of the frame and the frame is less likely to...
  20. I had the HPP one on my v1 pretty much it's...

    I had the HPP one on my v1 pretty much it's entire life. I had a few crashes/lawn dart landings where it popped out of the end cap. I don't know if it help or hurt, but I do know after 3 years, my...
  21. Replies
    10
    Views
    329

    Thinner oil in the shocks may help with the...

    Thinner oil in the shocks may help with the bouncing. I went too stiff on it and my stampede, made them really bouncy. Before drilling out the vdk, I was in no-mans land trying to figure out what...
  22. Replies
    30
    Views
    987

    Yep. If the linkage is setup right and the servo...

    Yep. If the linkage is setup right and the servo is working.
  23. Replies
    15
    Views
    1,063

    That's crazy! Nice work!

    That's crazy! Nice work!
  24. Replies
    30
    Views
    987

    Does it have the "optidrive" module in it? It's...

    Does it have the "optidrive" module in it? It's an electric box that keeps you from shifting into/from reverse when the transmission is spinning. Those were known to be kind of fussy and to cause...
  25. Replies
    10
    Views
    329

    I got some hard anno'd revo shocks on my eJato...

    I got some hard anno'd revo shocks on my eJato with trencher 3.8's. I run it on 3S with a 3200kv motor and the hot racing steel single speed conversion. I don't have it geared stupid high as I like...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4