Search:

Type: Posts; User: Rubberman04

Page 1 of 13 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    3
    Views
    943

    UPdate: If i unplug the leads doing to the...

    UPdate:

    If i unplug the leads doing to the motor and give it full throttle. My multimeter gives me 8.2v that would go to the motor. If i hook back the leads and give it full throttle then it...
  2. Replies
    3
    Views
    943

    Sorry i have not responded. Been busy and forgot...

    Sorry i have not responded. Been busy and forgot about my thread. My lipo reads 8.4v after a charge so im thinking it should be ok. And my nicad battery reads good too after a charge. THe reason i...
  3. Replies
    3
    Views
    943

    XL-5 not holding settings.

    On my Slash, Everytime i insert a battery either a Lipo or nicd it will not respond to the transmitter. Seems i have to reprogram it each and everytime. Then when i do get it programmed the...
  4. Replies
    6
    Views
    1,799

    battery connector question

    My buddy races his slash at a local track and uses the Lipo batteries. He changed the connectors to the Deans type. So is there any good reason to replace the Traxxas connector on the speed control...
  5. Replies
    27
    Views
    2,649

    i did it. it was the only option left and it runs...

    i did it. it was the only option left and it runs great now.
  6. Replies
    27
    Views
    2,649

    After a replacing the sleeve/piston, sealing the...

    After a replacing the sleeve/piston, sealing the exhaust manifold, sealing the backplate. This motor runs pretty now. It has a good idle and stays around the 270* area
  7. Replies
    27
    Views
    2,649

    I also sprayed wd40 around the base of the carb...

    I also sprayed wd40 around the base of the carb and backplate which the engine did not die. Anyone got ideas?
  8. Replies
    27
    Views
    2,649

    http://www.youtube.com/watch?v=ZvsxOSbxbFU

    http://www.youtube.com/watch?v=ZvsxOSbxbFU
  9. Replies
    27
    Views
    2,649

    The carb has all new Orings. I just pulled the...

    The carb has all new Orings. I just pulled the tank/fuel lines and air tested in a sink full of water. All is good there.
  10. Replies
    27
    Views
    2,649

    Hitting temps over 300*

    Just replaced the carb body and got new 20% fuel. As I have her idling there adjusting the idle set screw and low end screw, the temps will hit 300+. I got the hi speed needle 5 turns out. Also...
  11. Replies
    5
    Views
    1,909

    what engine parts are interchangeable?

    Thinking about upgrading the Tmaxx from the 2.5 to 3.3. So it looks like the interchangeable parts are:
    -Carb
    -clutch assembly
    -flywheel
    -carb pinch bolt
    -front/rear main bearings
    -air filter...
  12. Replies
    27
    Views
    3,117

    i did this yrs ago on the pro.15 and boy did it...

    i did this yrs ago on the pro.15 and boy did it make a difference. It sucked thru gas too.
  13. Replies
    1,189
    Views
    879,338

    Sticky: Here is my tmaxx after rebuilding it off and on...

    Here is my tmaxx after rebuilding it off and on for a year. I bought it from my neighbor for $50 and adding my 2.5, replacing broken or wrong parts and just fixin her up.
    ...
  14. Replies
    7
    Views
    268

    check those silver side caps. Mine was leaking...

    check those silver side caps. Mine was leaking even with a new Oring. I had fuel drip out while priming. Other than that i would think fuel tubing or fuel tank.
  15. Replies
    9
    Views
    1,460

    Well i used some black silicone RV caulk and it...

    Well i used some black silicone RV caulk and it didn;t work. Best to get a new carb body i think.
  16. Replies
    9
    Views
    1,460

    im gonna just JB Weld it. Just making sure i dont...

    im gonna just JB Weld it. Just making sure i dont let it seep into hole.
  17. Replies
    9
    Views
    1,460

    good question.

    good question.
  18. Replies
    17
    Views
    519

    maybe its idling too high then. The rollers on...

    maybe its idling too high then. The rollers on the fork are fine. thanks for your help.
  19. Replies
    17
    Views
    519

    ok well i got that Idler gear installed but it...

    ok well i got that Idler gear installed but it seems to stick in one gear or the other. The servo is doing its job by pushing the fork all the way in or out but it seems it stick. So if i put it in...
  20. Thread: loose lsn

    by Rubberman04
    Replies
    5
    Views
    1,469

    traxxas part 5247. it includes all the Orings for...

    traxxas part 5247. it includes all the Orings for the carb.
  21. Replies
    9
    Views
    1,460

    carb end cap

    I have a stripped end cap(silver cap) on the carb that doesnt stay in. Instead of replacing the carb body, can i glue that end cap in place?
  22. Replies
    17
    Views
    519

    thank you guys. I'll order that plus the bearing.

    thank you guys. I'll order that plus the bearing.
  23. Replies
    17
    Views
    519

    ok here it is: 3 groups of gears-...

    ok here it is:

    3 groups of gears-
    http://www.freeimagehosting.net/t/rvqcc.jpg

    Here is the case that has no idler gear and just a bolt/nut.
    http://www.freeimagehosting.net/t/codme.jpg
  24. Replies
    17
    Views
    519

    Ok im looking at the diagram and i see the idler...

    Ok im looking at the diagram and i see the idler gear and it doesnt look familar when i opened the tranny. I'll go look again.

    maybe i should pull apart the tranny again and take pics so you can...
  25. Replies
    17
    Views
    519

    engine is running.

    engine is running.
Results 1 to 25 of 309
Page 1 of 13 1 2 3 4