Search:

Type: Posts; User: 222

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    2
    Views
    168

    Sounds like either a stripped spur gear or one...

    Sounds like either a stripped spur gear or one that is missing a tooth, or one of your diffs is going out, most likely the rear one.
  2. If it runs off the receiver then itís most likely...

    If it runs off the receiver then itís most likely 6v, and for low beams just drop the voltage a bit. 5v should do the trick.
  3. Thread: Fried Rx, ESC??

    by 222
    Replies
    4
    Views
    216

    So sorry. Was looking at the specs for the max...

    So sorry. Was looking at the specs for the max 6. You are 110% correct. Max 5 is 200a ESC. Definitely want XT150ís or 8mm bullet connectors for it. No way XT90ís to traxxas adapters going to...
  4. At 6yrs old I would venture to say your battery...

    At 6yrs old I would venture to say your battery needs to be replaced. Itís most likely not holding voltage under a load, thus the reason you can see the tires spin fast when itís off the ground. ...
  5. Thread: Fried Rx, ESC??

    by 222
    Replies
    4
    Views
    216

    Get rid of the adapters. I would solder traxxas...

    Get rid of the adapters. I would solder traxxas connectors or XT150ís onto both the ESC and batteries. The way you have it now itís a choke point. You may be starving the ESC for power this...
  6. Thread: 17mm wrench

    by 222
    Replies
    6
    Views
    355

    Get yourself a thin walled 17mm socket, a 6Ē...

    Get yourself a thin walled 17mm socket, a 6Ē extension, and a 3/8 ratchet. You can find the socket off eBay for relatively cheap as well as the 6Ē extension. Something like this may not require an...
  7. Replies
    33
    Views
    1,012

    If you want to keep it all traxxas and want a...

    If you want to keep it all traxxas and want a good upgrade, look into the 2255 servo. Itís a normal size one, the kit for installing it may or may not have come with the truck.
  8. Replies
    6
    Views
    262

    SMC batteries has some 4800mah ones for under...

    SMC batteries has some 4800mah ones for under $30. They make pretty good batteries. ...
  9. Replies
    5
    Views
    509

    One is plenty. I used a JR 9000t for a long time...

    One is plenty. I used a JR 9000t for a long time on my 1st gen Erevo. Worked perfect. And it was only 300oz of torque. 400oz of torque at 6vdc is plenty. Donít see where traxxas lists the amount...
  10. Replies
    6
    Views
    262

    Try SMC or Gens Ace. I know that SMC are quality...

    Try SMC or Gens Ace. I know that SMC are quality batteries. Iíve heard good things about Gens Ace. There are other places to get batteries for cheap, but we are not allowed to speak of that place. ...
  11. Replies
    13
    Views
    485

    When you first get it, charge it at low at a low...

    When you first get it, charge it at low at a low amperage. Like no more then 1a. This will ensure that it doesnít get hot while charging. Heat is bad for them as with all batteries. It will take...
  12. Replies
    5
    Views
    248

    There is a big difference between ďrestingĒ...

    There is a big difference between ďrestingĒ voltage, and voltage ďunder loadĒ. Your batts may well have been hitting the LVC when you applied power as said above. A quality battery is a good...
  13. Replies
    10
    Views
    661

    Well for one in your first post you state that...

    Well for one in your first post you state that the spur gear you replaced the one that got chewed up with was not the stock 38t but rather a 36t. You should have had to set the mesh for this one. ...
  14. Replies
    10
    Views
    661

    Well said!!!

    Well said!!!
  15. The MIP drivers will no doubt remove the screws. ...

    The MIP drivers will no doubt remove the screws. Just bought my first one, and I will say they are made very well!! I also use RDS hex drivers, and they are well made too. You pay more for them,...
  16. Replies
    10
    Views
    661

    Just remember if there is another underlying...

    Just remember if there is another underlying issue you havenít found and you replace the plastic spur gear with a metal one, you will be more likely to do more damage to your vehicle. At least with...
  17. Replies
    11
    Views
    354

    It depends. You have good traction on the tires?...

    It depends. You have good traction on the tires? If not, then no, it wonít wheelie. Try it with a 3s. But make sure your tires have good grip before you do.
  18. Thread: Motor Failure

    by 222
    Replies
    80
    Views
    2,420

    A lot of people burn the stock servos due to not...

    A lot of people burn the stock servos due to not aligning them before using the truck out of the box. It takes some time to setup at dual steering servo setup and get it right. I run dual savox...
  19. Replies
    6
    Views
    351

    Oh man I am so sorry. I didnít realize there...

    Oh man I am so sorry. I didnít realize there wasnít a kit for the 2.0. Itís that much different I take it versus the OG. I know it made a world of difference on my 1st gen one. Someone should...
  20. Use 91% alcohol on the parts that require...

    Use 91% alcohol on the parts that require loctite. This will clean any residual oil off, whether it be from the parts or your hands and such.
  21. Replies
    6
    Views
    351

    Also adding the sway bar kit may help too.

    Also adding the sway bar kit may help too.
  22. Replies
    11
    Views
    354

    Bone stock the slipper clutch is setup to slip. ...

    Bone stock the slipper clutch is setup to slip. This is why others have said to tighten it down. Itís made that way to avoid breaking other parts. Really Nothing to do with being ďbone stockĒ. An...
  23. Replies
    5
    Views
    227

    Just be mindful about the hitec. Make sure itís...

    Just be mindful about the hitec. Make sure itís a digital servo. If not youíll have issues with it! Been there and done that!!!
  24. Replies
    8
    Views
    371

    Iíve run them on an 1st gen Erevo on 4s, dirt,...

    Iíve run them on an 1st gen Erevo on 4s, dirt, grass, and a little pavement. They work well on dirt and grass, and as said, they make a good kind of drifting tire on asphalt. Mine came off an older...
  25. The screws for your current motor should fit the...

    The screws for your current motor should fit the new motor.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4