Search:

Type: Posts; User: scissor34

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. Replies
    15
    Views
    868

    I appreciate that, and I have pretty good...

    I appreciate that, and I have pretty good knowledge of all the trucks I own and do use everyone else’s knowledge here when I get stuck on something. It’s probably unreasonable of me, because I know...
  2. Replies
    15
    Views
    868

    I understand that feeling too. I had pneumonia...

    I understand that feeling too. I had pneumonia really bad last fall that collapsed both of my lungs, shut down my kidneys and liver, then got infected with sepsis. I was given a 10% chance of making...
  3. Thread: Driveshaft ?

    by scissor34
    Replies
    2
    Views
    164

    Driveshaft ?

    I have the original HCG platinum Slash, are the driveshafts the same part # as the LCG? I know I should go metal but Iím not quite ready to at this time. Thanks in advance.
  4. Replies
    14
    Views
    378

    Ok thanks. The new pads made a world of...

    Ok thanks. The new pads made a world of difference, I figured I’d save the old ones after I roughed them up for spares.
  5. Replies
    12
    Views
    491

    Thank you!

    Thank you!
  6. Replies
    14
    Views
    378

    I’m not sure. I bought the replacement pads...

    I’m not sure. I bought the replacement pads directly from Traxxas part #5552x.
  7. Replies
    14
    Views
    378

    It seemed to grip better after a few minutes of...

    It seemed to grip better after a few minutes of running it. My pads weren’t anywhere near worn down to the pins they set on, but, I just replaced them with new. I haven’t had a chance to run it yet....
  8. Replies
    14
    Views
    378

    As always, I appreciate your help and knowledge.

    As always, I appreciate your help and knowledge.
  9. Replies
    14
    Views
    378

    Ok thanks, Iíll try that. Will the pads show...

    Ok thanks, Iíll try that. Will the pads show noticeable wear when they need to be replaced?
  10. Replies
    14
    Views
    378

    I’m having the same issue. Do the pads show...

    I’m having the same issue. Do the pads show noticeable wear like break pads do on full size vehicles? I seem to have a lot of pad left but they don’t seem to want to grip regardless of how much I...
  11. Replies
    12
    Views
    491

    Will you show a picture of what you did please?...

    Will you show a picture of what you did please? I’ve learned a lot from all of your posts I’ve read and appreciate your knowledge.
  12. Replies
    7
    Views
    236

    +1 on SMC. The 7200 2s 90c smoke the Floureon and...

    +1 on SMC. The 7200 2s 90c smoke the Floureon and Venom batteries I have. I had an issue with one of the 3s 7400 90c, but they replaced it, it’s ridiculously fast on a stock setup.
  13. Replies
    11
    Views
    319

    Ok, good idea. I plugged it into right side of...

    Ok, good idea. I plugged it into right side of one of the 3 prong channels with the red positive wire connecting to the middle prong. I tried posting a picture but I don’t think I can yet because of...
  14. Replies
    11
    Views
    319

    I got it working, thanks for everyone’s help.

    I got it working, thanks for everyone’s help.
  15. Replies
    11
    Views
    259

    Ok I got it with a shorter screw that came off my...

    Ok I got it with a shorter screw that came off my Revo 3.3 I think. One more question, does anyone make a cap or something to protect the balancing plug on lipo batteries so they don’t get packed...
  16. Replies
    11
    Views
    319

    I should be more clear in what I’m asking. So my...

    I should be more clear in what I’m asking. So my esc fan is plugged into the esc input, but I’m not sure where to plug the motor fan into on the receiver. The receiver has three prongs and the fan...
  17. Replies
    11
    Views
    319

    Fan install question

    I have a fan on my esc that is plugged into the output wire from the esc, I bought a dual fan Heatsink for the motor. My question is where should I plug that wire into my receiver? Itís a 5 channel...
  18. Replies
    11
    Views
    259

    Ok thanks. You don’t happen to have a picture of...

    Ok thanks. You don’t happen to have a picture of what you or anyone else is using as far as a spacer or nut do you?
  19. Replies
    11
    Views
    259

    One more question, until I get the LCG chassis, I...

    One more question, until I get the LCG chassis, I got an HR aluminum motor mount , everything fit perfectly except it seems like the stock screw that allows adjustment for pinion and spur mesh seems...
  20. Replies
    11
    Views
    259

    Great, thanks to everyone for their help!

    Great, thanks to everyone for their help!
  21. Replies
    11
    Views
    259

    Ok thanks.

    Ok thanks.
  22. Replies
    11
    Views
    259

    Converting to LCG Chassis help

    I have an original Slash 4x4 Platinum HCG that Iím thinking of converting to the LCG chassis and have looked at different ďkits or setsĒ and have a few questions. If anyone has a link to steer me in...
  23. Replies
    6
    Views
    377

    Yes throttle control is a skill I lack, I’m a...

    Yes throttle control is a skill I lack, I’m a throttle masher. Actually we both are and my buddy is just getting into rc’s so he’s really into the high power 6s stuff. That video was actually my...
  24. Replies
    6
    Views
    377

    Here’s where we’re running....

    Here’s where we’re running. https://youtu.be/jKa9kT-KRig
  25. Thread: Slash set up

    by scissor34
    Replies
    0
    Views
    128

    Slash set up

    I mistakenly posted this same question in the regular slash forum, but I have a hcg slash 4x4 Platinum and am looking for advice. My front yard has become a makeshift figure 8 rc track and Iím going...
Results 1 to 25 of 35
Page 1 of 2 1 2