Search:

Type: Posts; User: O.G.

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. Replies
    11
    Views
    1,171

    I have the skil derived mentioned above and it...

    I have the skil derived mentioned above and it absolutely has saved my carpel tunnel hands. You can buy attachments to fit the screw heads and as I recall, most of the traxxas velineon screws use the...
  2. Replies
    4
    Views
    265

    Try removing the body. Air will sometimes get...

    Try removing the body. Air will sometimes get underneath and lift your tires causing you to lose traction. Also, as mentioned above you need a longer straightaway.


    Sent from my iPhone using...
  3. Replies
    13
    Views
    875

    I use duct tape to reinforce bodies. Sent...

    I use duct tape to reinforce bodies.


    Sent from my iPhone using Tapatalk
  4. Thread: Clicking sound.

    by O.G.
    Replies
    21
    Views
    947

    Is the battery fully charged?? The driving...

    Is the battery fully charged?? The driving problem sounds like a bad battery, but the combined symptoms sounds like a bad esc.


    Sent from my iPhone using Tapatalk
  5. I tried a set of their 17mm axle adapters and...

    I tried a set of their 17mm axle adapters and they kept spinning off with each run. And the threads were half-stripped when I opened the box. Some Integy parts are okay, but there is such a large...
  6. Replies
    6
    Views
    947

    If you have an RPM bumper, flip it upside down...

    If you have an RPM bumper, flip it upside down for a bit of downward pressure, and zip tie a small wrench to the front end for weight.


    Sent from my iPhone using Tapatalk
  7. 1. If you keep your truck up on a stand, the rpm...

    1. If you keep your truck up on a stand, the rpm A-arms won't warp. 2. Did you say you have a Velineon 4-pole motor but you're still using the 2-pole?? I'd change out to the 4-pole for more power...
  8. Replies
    13
    Views
    769

    You could upgrade to 17mm wheel hubs and then use...

    You could upgrade to 17mm wheel hubs and then use buggy tires. They'll look great on your truck.


    Sent from my iPhone using Tapatalk
  9. Replies
    11
    Views
    1,058

    I'd start with a small drill bit and then go...

    I'd start with a small drill bit and then go bigger.


    Sent from my iPhone using Tapatalk
  10. Replies
    15
    Views
    1,739

    All my truck have lipos, bearings and brushless...

    All my truck have lipos, bearings and brushless systems now. Some started as XL5's but that didn't last long.


    Sent from my iPhone using Tapatalk
  11. Replies
    12
    Views
    344

    25 pinion on 3s? You must be smokin out there....

    25 pinion on 3s? You must be smokin out there. That's a lot of speed. What size spur gear r u running?


    Sent from my iPhone using Tapatalk
  12. Thread: Motor cooling

    by O.G.
    Replies
    18
    Views
    552

    No those are the correct size tires. I would...

    No those are the correct size tires. I would consider an aluminum transmission case which really brings the temps down. There are several options and price ranges like the FLM and HR cases.

    ...
  13. Replies
    2
    Views
    153

    Yes. You'll use the teflon washers. Use the chart...

    Yes. You'll use the teflon washers. Use the chart on this website for the VXL Rustler for perspective.


    Sent from my iPhone using Tapatalk
  14. There is the silver disc and pads that could be...

    There is the silver disc and pads that could be causing the problem. See if the disc is warped which could push the spur out of alignment. The lay shaft could be bent, I'd just replace it to see if...
  15. Replies
    15
    Views
    1,370

    When installing the STRC pins I had to clean up...

    When installing the STRC pins I had to clean up the plastic slots with a drill bit. I've forgotten the correct size. And if you use a drill be very careful and go very slowly. Only a single rotation...
  16. When I received the FLM, is was beautifully...

    When I received the FLM, is was beautifully machined, but not sealed. So no real improvement over stock. Plus you couldn't see it and enjoy how it looks.


    Sent from my iPhone using Tapatalk
  17. Are the radios the same version/brand? Sent...

    Are the radios the same version/brand?


    Sent from my iPhone using Tapatalk
  18. Replies
    5
    Views
    358

    I haven't tried the new version that has the...

    I haven't tried the new version that has the servo saver in it. I have the TRX and STRC aluminum versions and they're solid.


    Sent from my iPhone using Tapatalk
  19. STRC, FLM for the good stuff, HR for budget. I...

    STRC, FLM for the good stuff, HR for budget. I buy a lot from AMain racing.


    Sent from my iPhone using Tapatalk
  20. Thread: Foam tires

    by O.G.
    Replies
    8
    Views
    496

    Did you buy a set?? Sent from my iPhone...

    Did you buy a set??


    Sent from my iPhone using Tapatalk
  21. what diff oil weight should i use for off road romping/speed runs?

    I settled on 50k for my diff fluid. The FLM didn't used to be sealed, maybe the new ones are. HR is also a good choice. The Swami wasn't sealed either. If they aren't sealed, your fluid will run out....
  22. I settled on 50k for my diff fluid. The FLM...

    I settled on 50k for my diff fluid. The FLM didn't used to be sealed, maybe the new ones are. HR is also a good choice. The Swami wasn't sealed either. If they are t sealed, your fluid will run out. ...
  23. Replies
    18
    Views
    766

    Does she know about every dollar you spend? Tell...

    Does she know about every dollar you spend? Tell her you got it on sale.


    Sent from my iPhone using Tapatalk
  24. Replies
    3
    Views
    411

    If you're racing on dirt, pins are a good choice,...

    If you're racing on dirt, pins are a good choice, or grooved tired on the front. Paddles on the rear for sand but you'll likely bind up every moving bearing on the truck if you do so. Trenchers for...
  25. Replies
    5
    Views
    431

    Once I remove the cover I never replace it. In...

    Once I remove the cover I never replace it. In fact I don't think any of my trucks still have the covers.


    Sent from my iPhone using Tapatalk
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4