Search:

Type: Posts; User: NitroStarGT

Page 1 of 3 1 2 3

Search: Search took 0.04 seconds.

  1. Replies
    70
    Views
    8,691

    I just bought a front set of GPM brand cvd's for...

    I just bought a front set of GPM brand cvd's for the front of my Slash or Rustler. Have decided which one to put them on LOL. I believe they are the same size??
  2. Replies
    18
    Views
    1,773

    Well I ran it on 2s and then 3s. Seemed a little...

    Well I ran it on 2s and then 3s. Seemed a little bit better but the lowered preload made it not roll over as much. Had a lot of fun. It is freezing outside LOL.
  3. Replies
    18
    Views
    1,773

    I poured the stock oils out and refilled the rear...

    I poured the stock oils out and refilled the rear with Losi 50w and the fronts with 40w. Set preload at drive shafts just above level. The drop test appears even with a 2s 5000mah lipo. Will run and...
  4. Replies
    18
    Views
    1,773

    I dunno what to try now??

    I dunno what to try now??
  5. Replies
    18
    Views
    1,773

    Owners manual says the Rustler 4x4 comes stock...

    Owners manual says the Rustler 4x4 comes stock with 50w in front shocks and 30w in the rear?? What up with this?
  6. What version of the Mamba and what exact motor do...

    What version of the Mamba and what exact motor do yall run? I have a Mamba SCT pro and a short can 36 or 3800 and feel it is overworked in a Salsh 4x4.
  7. I just bought the Traxxas VXL fan and a Castle...

    I just bought the Traxxas VXL fan and a Castle single fan shroud for the motor at Hobbytown.
  8. Replies
    7
    Views
    800

    Owners manual says stock 8s truck: "From the...

    Owners manual says stock 8s truck:
    "From the factory, the front differential is filled with SAE 10,000W viscosity silicone oil. The rear differential is filled with 30,000W oil."

    I changed my...
  9. Replies
    4
    Views
    516

    I had to quit using my bluetooth around May of...

    I had to quit using my bluetooth around May of last year after they fixed the receiver/ESC glitching issue causing the truck to quickly slam brakes. Everything worked good and truck runs fans and...
  10. I am NOT able to adjust low voltage cut-off using...

    I am NOT able to adjust low voltage cut-off using the bluetooth module and app.
  11. Replies
    23
    Views
    2,001

    Update: The STRC 3640RBK Hinge Pins fit both the...

    Update: The STRC 3640RBK Hinge Pins fit both the front and rear of the Slash 4x4. You cannot tighten them down real tight, but they fit and are the correct diameter. These must be the same size as...
  12. Replies
    23
    Views
    2,001

    I ordered "STRC 3640RBK Hinge Pins, Slash 4x4...

    I ordered "STRC 3640RBK Hinge Pins, Slash 4x4 (BK)" for the rear, cause it says it in description and on package. But from what I'm reading here, they are do big in diameter. I ordered 3640-FO for...
  13. What motor mount/center diff, front bearing...

    What motor mount/center diff, front bearing holder do you use and what drive shaft?
  14. This is a great thread! Thanks for your...

    This is a great thread! Thanks for your commitment. Subbed you on Youtube also.
  15. Replies
    7
    Views
    801

    Sounds like the X-Maxx 8s ESC and motor would be...

    Sounds like the X-Maxx 8s ESC and motor would be a GREAT combo for the E-Revo LOL. I might just swap it over and just buy a new combo for the X-Maxx.
    But back on your issue, I would definately get...
  16. Dynamite metric hex driver set. The all metal...

    Dynamite metric hex driver set. The all metal handled ones are best for the money (around $20).
    The best ones period are MIP metric hex driver set (around $45)
  17. Thread: need help

    by NitroStarGT
    Replies
    2
    Views
    531

    Manual states how to reset the radio BUT I was on...

    Manual states how to reset the radio BUT I was on the phone with Traxxas one time and he told me how to do a "Master Reset". It wasn't hard but I forgot how to do it. Call them and they should hook...
  18. Replies
    13
    Views
    1,419

    Great info on the original thread. Thanks again

    Great info on the original thread. Thanks again
  19. Replies
    13
    Views
    1,419

    I have the 85mm straps installed on the aluminum...

    I have the 85mm straps installed on the aluminum brace. I had some spacers in my RC box. Stole some longer screws out of another RC chassis. I have since pulled the left rear pushrod end off twice....
  20. Replies
    13
    Views
    1,419

    This is great information! Ya think you could...

    This is great information! Ya think you could weigh both stock and Shockwave mounted tire and report back? I've got Shockwaves in my wish lists now!
  21. Replies
    2
    Views
    3,102

    Take the rear push rod ends off, while putting...

    Take the rear push rod ends off, while putting your limiting straps on, and dampen with water and put some gorilla glue on the threads and screws back on and let sit for 2 hours before stressing them.
  22. Replies
    5
    Views
    795

    My left rear bottom rod end has pulled out again...

    My left rear bottom rod end has pulled out again after installing a new end. It has actual threads because it threaded on when screwing to the right. BUT the threads are very shallow. I will call...
  23. Replies
    1
    Views
    294

    I just put some new ones on the bottom rear and...

    I just put some new ones on the bottom rear and used Original Gorilla Glue. Waiting for an hour or two before trying it out.
  24. Replies
    16
    Views
    3,207

    New updates on the Taxxas Link app for...

    New updates on the Taxxas Link app for Transmitter, Receiver, and ESC when I checked today. Updated my E-Revo but my reverse is still only 50%. Anybody know where we can get release notes?
  25. Thread: Servo help

    by NitroStarGT
    Replies
    3
    Views
    387

    Mine was pretty short that I installed in my Losi...

    Mine was pretty short that I installed in my Losi Rock Rey. Had to buy a 3 or 6" extension for it. I would think you would need an extension for, at least, the port side servo on the Revo.
Results 1 to 25 of 63
Page 1 of 3 1 2 3