Search:

Type: Posts; User: 1daniel14

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    20
    Views
    907

    They have definitely been installed in it then,...

    They have definitely been installed in it then, thats not a nitro thing lol.
  2. Replies
    14
    Views
    1,676

    I have found that running tubing with a smaller...

    I have found that running tubing with a smaller inner dia. can play havoc with a 3.3, ive had them lean out and stall at WOT/High revs due to running out of fuel.

    Length should have very little...
  3. Replies
    20
    Views
    907

    It probably made it a bit hard that the nitro...

    It probably made it a bit hard that the nitro diff cup is empty,

    But its basically just the nitro one on the left doesnt have those steel inserts, it doesnt have the steel support in the center...
  4. Replies
    18
    Views
    2,425

    You cant successfully drill the passages into the...

    You cant successfully drill the passages into the head, there isnt enough there..

    It makes it really hard to fit other heads as the 3.3 uses a 5-bolt pattern.

    the best luck you will have is...
  5. Replies
    20
    Views
    907

    Revo Diff Vs. E-Revo Diff - Pics.

    For those who are having diff problems are looking for an alternative the E-Revo diff is definitely the way to go :)

    Here are some shots i got of a brand new E-Revo Diff next to a Stock Nitro...
  6. Replies
    18
    Views
    1,181

    As the pinion slides off its going to strip it,...

    As the pinion slides off its going to strip it, because theres less spur being driven, if you get what i mean...

    I bet it stripped when the pinion/spur had only about half of the teeth lined up ;)
  7. Replies
    19
    Views
    656

    Losi hubs (atleast the Muggy anyway) come...

    Losi hubs (atleast the Muggy anyway) come pre-threadlocked with a little coating of blue.

    I cant see any harm in that, but its not really necessary, i havent had too much trouble with mine and BB...
  8. Replies
    18
    Views
    1,181

    You should just red loctite the pinion in place,...

    You should just red loctite the pinion in place, set the mesh as tight as you can while still having no resistance and noise-free, and stick with the plastic spurs, they are like the "fuse" of the...
  9. Replies
    9
    Views
    1,213

    Having the bad exhaust coupler will cause it to...

    Having the bad exhaust coupler will cause it to run lean from the lack of pressure in the fuel tank, seal it back up and try again, while its idling keep richening the LSN bit by bit till it stalls,...
  10. Replies
    28
    Views
    2,764

    If the diff lockers start showing signs of...

    If the diff lockers start showing signs of weakness i guess the next is mini spool's ;)
  11. Replies
    52
    Views
    975

    Yeah, which is not so bad...that way you dont...

    Yeah, which is not so bad...that way you dont need the bellcrank, or get hold of a slide carb.
  12. Replies
    15
    Views
    763

    Nope, $1 :lol: Its not so much as the...

    Nope, $1 :lol:



    Its not so much as the "easy" way but the better way, and it looks just like any other clutch setup does with the exception of a 4mm spacer bearing, and no, the 3rd bearing...
  13. Replies
    15
    Views
    763

    yeah if they run the same they would be the same...

    yeah if they run the same they would be the same bar the pin on the crank for starting...it would be a noticable difference.

    Cheers.
  14. Replies
    15
    Views
    763

    Out of curiosity has anyone noticed any...

    Out of curiosity has anyone noticed any performance differences switching between TM/TZ crank? im not totally sure if the timing is identical.
  15. Replies
    15
    Views
    763

    The TM crank makes it a TON easier cause the...

    The TM crank makes it a TON easier cause the stock clutch setup fits real good.

    Im looking for a TZ crankcase, bearings, and Piston/Sleeve and gonna throw in my old dead TM parts and make a...
  16. Replies
    15
    Views
    763

    No one suggested it is a BB motor...it fits the...

    No one suggested it is a BB motor...it fits the stock mounts fine, and you dont have to cut the crank, which is why i mentioned the bearing.

    I have a TZ at home with the stock flywheel, a short...
  17. Replies
    19
    Views
    656

    My MBX5T uses a different thread pitch to Ofna,...

    My MBX5T uses a different thread pitch to Ofna, Ofna ones are alot coarser. Never tried them with Losi hexes, i guess i could when i get home.
  18. I boil them for about 15 minutes then try to pull...

    I boil them for about 15 minutes then try to pull them off, it isnt usually easy, 99% of the time i have to put the wheel back in few 5 minutes or so.

    Since using 401 and 406 Loctite (strongest...
  19. Replies
    52
    Views
    975

    For what its worth, you dont need to modify the...

    For what its worth, you dont need to modify the TZ to fit the revo, or vice versa...

    You just need a bump starter, or get the TZ-TX pullstart version.
  20. Replies
    15
    Views
    763

    The TZ will drop right in as-is, you just need to...

    The TZ will drop right in as-is, you just need to get a big block clutch nut, and use a 3rd clutch bearing as a spacer outside the clutch bell, but that depends on how thick the flywheel is, etc.
    ...
  21. Replies
    6
    Views
    586

    What? The outside diameter of the rim is 3.7...

    What? The outside diameter of the rim is 3.7 inch, where as the traxxas rims are 3.8 inch... 2.2 inch is stadium truck size, like the older rustlers etc have.
  22. Replies
    6
    Views
    586

    Has anyone tried it? because LPR's are 3.7"......

    Has anyone tried it? because LPR's are 3.7"... IDK if thats enough of a difference to worry about.
  23. Replies
    19
    Views
    656

    I have access to the RC8T but not to any traxxas...

    I have access to the RC8T but not to any traxxas hexes ;)

    Just put an "X" on the backside of them like Revoroller said so that it bits into the rim, and do them up real tight.
  24. Replies
    4
    Views
    482

    Really no way to avoid it bro, you can run the...

    Really no way to avoid it bro, you can run the pipe on the other side of the engine, with the pipe going up the center of the chassis, and put a long deflector out the side, but then you gotta put...
  25. Those tires look like the Savage tires i had,...

    Those tires look like the Savage tires i had, they hooked up real good for a while, was running brushless with plastic 14mm hexes so they didnt last long :(
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4