Search:

Type: Posts; User: dacaur

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    7
    Views
    1,729

    The only change they ever made to the mini revo...

    The only change they ever made to the mini revo was the rear bulkheads. They added a screw to try and eliminate the rear diff stripping issues (with limited success)
    I have one of the first gen...
  2. Replies
    4
    Views
    1,271

    There is no "right" amount. The whole reason we...

    There is no "right" amount. The whole reason we need to shim the mini revo diffs is because manufacturing tolerances and plastic flex allow the teeth to skip... IF there was an exact right number of...
  3. Replies
    2
    Views
    725

    Longer travel summit rockers and larger tires.......

    Longer travel summit rockers and larger tires.... I run big joe II's.... Does great on the rough stuff.... The mini revo is set up for a dirt race track, not a construction lot....
  4. Replies
    2
    Views
    1,171

    as long as the set screw is on the shaft, you...

    as long as the set screw is on the shaft, you will be fine.
  5. Replies
    12
    Views
    4,333

    Aluminum a-arms wont flex, they will bend, and...

    Aluminum a-arms wont flex, they will bend, and stay bent. If you plan to jump your truck, you dont want aluminum arms.
  6. Replies
    6
    Views
    2,772

    It doesnt sound like he plugged in the servo...

    It doesnt sound like he plugged in the servo wrong, I think by "Forward is now left and backwards is now right which isn't what I want." He means that when he turns the wheel "forward" it turns left...
  7. Replies
    3
    Views
    633

    yea thats normal brushless motor sounds. Being a...

    yea thats normal brushless motor sounds. Being a sensorless motor, its not made to run at really low speeds....

    It appears that when you pull the trigger further, the car goes, so unless you are...
  8. Replies
    1
    Views
    440

    pulled out some black plastic from where?

    pulled out some black plastic from where?
  9. Replies
    3
    Views
    473

    did you completely tighten the screws that hold...

    did you completely tighten the screws that hold the bulkhead together? Unless there was a defent in the gears during manufacturing, there is no way they should go out that fast in the front if...
  10. Replies
    17
    Views
    1,451

    aluminum is probably a good idea for the rear if...

    aluminum is probably a good idea for the rear if you run on 3 cells, but not necessary for the front.
  11. Replies
    17
    Views
    1,451

    if you put the diff in backward, you would know...

    if you put the diff in backward, you would know it. The front would try to go in reverse when you went forward, the truck wouldn't go. The driveshafts dont need to be "lined up", as long as the...
  12. Replies
    17
    Views
    1,451

    You should never have trouble with your front...

    You should never have trouble with your front diff, all the stress goes on the rear. No you dont need to shim the front. With a center diff that takes even more stress off the front diff.... Why did...
  13. Replies
    12
    Views
    4,333

    First thing I would do is screw in all rear...

    First thing I would do is screw in all rear pillow balls a turn or two. I assume when you installed the RPM arms you did follow the directions on the number of turns you need to screw in each one?...
  14. Replies
    12
    Views
    4,333

    yep. get the mini revo progressive rockers.

    yep. get the mini revo progressive rockers.
  15. Replies
    17
    Views
    1,451

    It sounds like you have a one way diff, not a...

    It sounds like you have a one way diff, not a center diff. A one way differential transfers power in the forward direction, but spins freely when it doesn't have power applied, which means when...
  16. Replies
    12
    Views
    4,333

    You could also just use the stock mini revo...

    You could also just use the stock mini revo plastic shafts. They are way better than the mini summit shafts, and you dont have to worry about them popping out....
  17. Replies
    11
    Views
    5,598

    Drive a 2 wheel drive on damp grass and you will...

    Drive a 2 wheel drive on damp grass and you will immediately see the advantage to 4 wheel drive, even without locked diffs.
    Re: diffs, Unless you are rock crawling (or otherwise moving slowly),...
  18. Replies
    3
    Views
    1,394

    I use the integy setup, but only because it was...

    I use the integy setup, but only because it was the only one that came in green. The hot racing one is just as good. My metal one has been great, I run big joe II's so broke 3 in quick succession...
  19. Thread: Plastic gears

    by dacaur
    Replies
    5
    Views
    758

    All gears in the diff are metal. Only the gears...

    All gears in the diff are metal. Only the gears in the transmission are plastic, and you will never strip those. The only gears that will ever strip on this truck when its properly set up are the...
  20. Replies
    8
    Views
    1,229

    This truck is not made to have the shocks absorb...

    This truck is not made to have the shocks absorb big jumps. Buggys and truggys (this is technicaly a truggy) are designed so the chassis slaps the ground when they land off jumps to absorb the...
  21. Replies
    3
    Views
    659

    Plus the savox runs the opposite way, so there is...

    Plus the savox runs the opposite way, so there is that...
  22. The only reason the mini summit beats the mini...

    The only reason the mini summit beats the mini revo in the grass is because the mini revo tires suck. You just have no traction. The mini revo makes headway in grass by pure wheel spin. Get some...
  23. I mean, if you REALLY watch the temps, you might...

    I mean, if you REALLY watch the temps, you might be ok, but of all terrains, grass is the one that is the MOST likely to overheat any RC...
  24. Yea I have never had a problem with the stock...

    Yea I have never had a problem with the stock plastic red ones. I am currently using the green plastic ones from the monster jam truck on mine because they match my green arms.
  25. Replies
    14
    Views
    2,855

    This is what you want...

    This is what you want https://www.amazon.com/Team-Associated-21141-Differential-324x-409x-005/dp/B000BOB6EO
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4