Search:

Type: Posts; User: Richard@JP

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    186

    Hiya Try a factory reset on the Transmitter...

    Hiya

    Try a factory reset on the Transmitter doing the endpoints too.
  2. Replies
    18
    Views
    533

    Dont be afraid to run a maxx on the 3s batteries,...

    Dont be afraid to run a maxx on the 3s batteries, its a bit slower but lighter so dosent really notice too much
  3. Replies
    20
    Views
    788

    50wt i would say is way to go tbh. Widemaxx kit...

    50wt i would say is way to go tbh.
    Widemaxx kit moves lower shock position outward for more stability and a better shock rate in compression
  4. Replies
    16
    Views
    728

    I would say Max 5 is way to go in X-maxx tbh

    I would say Max 5 is way to go in X-maxx tbh
  5. Its only super heavy or poor landings that cause...

    Its only super heavy or poor landings that cause the chassis to flex enough to bend the shaft.
    If it was a metal chassis car like a A**** it would have bent the chassis instead.
  6. Replies
    8
    Views
    255

    When setting trim or endpoints TSM must be off...

    When setting trim or endpoints TSM must be off otherwise it will drift like you have
  7. Change to 8996X as you break the wider plastic....

    Change to 8996X as you break the wider plastic.
    The 8996X are soooooo much better tho
  8. Replies
    5
    Views
    212

    I would say there is some parts missing...

    I would say there is some parts missing especially as thats a plastic gear.
  9. Replies
    12
    Views
    393

    rx has crashed

    rx has crashed
  10. Hiya Check the motor isnt seized as well

    Hiya

    Check the motor isnt seized as well
  11. Replies
    3
    Views
    214

    Hiya In a maxx? Very unusual tbh can you...

    Hiya

    In a maxx?
    Very unusual tbh can you post pics

    Richard
  12. Replies
    16
    Views
    728

    Hi The max 5 is brilliant in the xmaxx more...

    Hi

    The max 5 is brilliant in the xmaxx more power and smoother.
    Just remember to keep the lead from the heatsink connected to traxxas rx otherwise goes into limp mode.
  13. The new traxxas hd arms tbh. Not a grainy finish...

    The new traxxas hd arms tbh.
    Not a grainy finish so stay looking better than rpm ones
  14. Replies
    34
    Views
    1,503

    Another cause of standard motor faliure is seized...

    Another cause of standard motor faliure is seized axle bearings
  15. Replies
    8
    Views
    660

    Hi We have both 7460a and 7460r in stock at uk...

    Hi

    We have both 7460a and 7460r in stock at uk importers so order with your local modelshop

    Rich
  16. Hiya These cars do get the motor quite hot, so...

    Hiya

    These cars do get the motor quite hot, so would suggest letting car cool down after 10 mins running.
  17. Replies
    8
    Views
    636

    Traxxas HD are better than rpm tbh and smooth...

    Traxxas HD are better than rpm tbh and smooth finish so can be cleaned easy
  18. Replies
    18
    Views
    587

    Hiya Usually its the case melted where the input...

    Hiya
    Usually its the case melted where the input shaft from slipper comes in on slipper side.
    Bearing fails and causes case to melt.
  19. The Traxxas batteries are good quality and the...

    The Traxxas batteries are good quality and the 6700s make the xmaxx run the best in my experience.
    An Xmaxx on 5000s is a real let down

    Richard
  20. Replies
    22
    Views
    1,215

    Hi You will loose steering with a saver fitted...

    Hi

    You will loose steering with a saver fitted as even the strongest will deflect whenthe axle moves over rough ground.
    If your that worried use the stock plastic servo horn as it will fail first.
  21. Hi Really i would suggest the Traxxas batts...

    Hi

    Really i would suggest the Traxxas batts whilst model is under warranty etc.
    Overlander batts are also very good.
  22. Replies
    22
    Views
    1,101

    Hiya The springs will sag a touch after first...

    Hiya

    The springs will sag a touch after first run you just need to adjust the preload collars back down on the shock body to raise the ride height
  23. Hiya Not enough voltage i would say. Normally...

    Hiya
    Not enough voltage i would say.
    Normally with an AXE i wire the red esc light kit lead into the fan port on AXE
  24. Replies
    9
    Views
    480

    Hi That usually only happens when chassis has...

    Hi
    That usually only happens when chassis has flexed a lot after a heavy landing and bent the prop shaft
  25. Replies
    6
    Views
    2,711

    Hiya ESC has failed sometimes taken out when...

    Hiya

    ESC has failed sometimes taken out when motor goes

    Richard
Results 1 to 25 of 37
Page 1 of 2 1 2