Search:

2wd 90t spur I would start with a 21t pinion that should get you about where you want to be with a 3800kv motor and stock Alias tires on 2s.

As a newcomer not much since you're not looking for crazy speeds and power. Just that in time you may get bored and want more and end up spending more in the long run then starting with say a VXL...

The other brand you speak of that starts with an A. I have a brushed one that converted to brushless. The brushed version is cheaper than the brushless one but not worth it. Too much difference...

Hobbywing MAX10 SCT esc or a Hobbwing WPSC8 and a 3660 (36mm dia 60mm long) size or larger brushless motor. Also there is a Slash 4X4 section of the forum you should post in there...

Servo in the CH1 spot second from the bottom, esc in the CH2 spot, the white wire on both facing the inside of the receiver then do throttle setup and try again.

Never had the Hot racing ones. I like the quality of the aluminum proline uses for the hex. The clamping is nice also. I like the flat face of the hex also not the rounded in face of some other hexes...

Try these 12mm hexes from proline https://www.ebay.com/itm/PRO6098-00-Pro-Line-PRO-2-Rear-Clamping-Hex-Set/401344243232?epid=1501472314&hash=item5d71fb2620:g:QQgAAOSwnK9ZOtc0 and blue (meduim)...

This is just me talking and my own opinion. But the 2wd drive line up uses a lot of the same parts. Buy spare parts for one can be used on another. Upgrading 2 drive shafts to something like MIP's vs...

If you go with a Kimbrough 124 I would suggest a metal gear servo or at least remember to set your steering end points (if not done already should do that anyways).

I understand I felt that way when I put the MG955 in my Circuit. In the end with a better servo it's just more enjoyable to drive. I won't really call anything throw it in the pool waterproof but it...

I had that Tower pro MG995 servo it was strong but slow and did not last long it was in a different brands stadium truck. I think you need to up your budget something like less than $20 shipped than...

If you have the TQ transmitter my guess would be because of the transmitter (TQ) not being able to set servo steering end points and/or not be able to limit steering travel. Having a transmitter that...

I have seen no difference in temp with the piece of Gorilla tape I used to cover the bearing hole but I usually just make use of smaller RPM stickers to cover the bearing hole. The pic is of a 3650...

I don't know if they changed the black chassis from the original Rustler or not but the old chassis I had to get rid of the ridges inside to fit my batteries also the the grey chassis on the newer...

Yeah Racing makes a heatsink like the Basten also...

I have a couple Floureon 2s 5200mah 30c lipos for a few years now work pretty well for me.

On your lipo and LVC issue get a cheap lipo alarm plug it in and see if your battery is dumping voltage...

I have only used the Traxxas aluminum and Hot Racing ones but GPM makes steel ones also never tried them though.

Yes they are

Support video page https://traxxas.com/support/video#/?playlistId=0&videoId=0

Steering reversal https://traxxas.com/support/video#/?playlistId=0&videoId=12

XL5 Throttle profiles...

Looks like a Prerunner to me (longer chassis than Teton).

Center driveshaft is longer because of the longer chassis the diff to the wheel shafts though are the same on the Teton and Prerunner...

They are the same lenghtwise the measurement 40mm is the case without the mounting tabs.

https://i.imgur.com/gVq0j3K.jpg

That connector is what they call a Tamiya connector (Tamiya plug) you can still find some batteries with that plug online. All the parts that are available now for the newer Rustler will fit except...

Fan model FS-15W

https://www.ebay.com/itm/FS-15W-15kg-0-12s-impermeable-High-Torque-Metal-Gear-Standard-Digital-Servo/322987238442?hash=item4b338a242a:g:xTYAAOSwBRVaU3xP&frcectupt=true

Use spacers under the platform. I needed a few mm's more to get my packs in/out and just used nylon spacers cut to the size I needed but you can use anything you want to use to get the spacing you...

Looks like a DS3218 servo instead of a Power HD servo.

https://www.amazon.com/s?k=ds3218+servo&i=toys-and-games&crid=2PUIWWPCTCOF2&sprefix=DS3218+%2Ctoys-and-games%2C162&ref=nb_sb_ss_i_1_7

Don't see anybody talking about running 4s in this thread. If your referring to the motor pics there just for reference of motor sizes.

As Gripdog said the 3660 2600kv can handle 4s. The 3650...