Search:

Type: Posts; User: Workingstiff

Page 1 of 7 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    15
    Views
    1,186

    I like the idea of the rheostat. I have the same...

    I like the idea of the rheostat. I have the same type of set up with my heater in my salt aquariums, for redundancy.
  2. Replies
    3
    Views
    383

    Perfect, thank you. Double post due to being in...

    Perfect, thank you.
    Double post due to being in and out of signal.
  3. Replies
    15
    Views
    1,186

    Thx,not new to soldering. Just time to spend some...

    Thx,not new to soldering. Just time to spend some $$$.
  4. Replies
    3
    Views
    383

    Soldering iron

    What soldering iron are you folks using? Basic requirements?
  5. Replies
    15
    Views
    1,186

    Soldering iron

    What soldering iron are you folks using? Basic requirements?
  6. Replies
    13
    Views
    701

    Kingz Head or Hot Racing?

    Kingz Head or Hot Racing?
  7. Replies
    6
    Views
    445

    I like it it, keeps junk out of the driveshaft...

    I like it it, keeps junk out of the driveshaft channel.
  8. Replies
    13
    Views
    701

    Nope,no screws. The part and 2 bearings.

    Nope,no screws. The part and 2 bearings.
  9. Replies
    13
    Views
    701

    It was a direct drop in except for that single...

    It was a direct drop in except for that single screw. Its a nice piece. I thought I remembered reading somewhere that folks needed to shorten up that screw. It's not a problem, just looking for...
  10. Replies
    13
    Views
    701

    Yep, both washers are on there. Its a knurled...

    Yep, both washers are on there. Its a knurled stainless steel screw,correct?
  11. Replies
    13
    Views
    701

    I just installed......

    a KHZ motor mount with the larger bearing. Am I remembering correctly, some of us need to shorten our mesh adjuster screw? It's bottoming out. Might need to take a full 1/16 to 3/32 off of it.
  12. Ok,thanks again, great job!

    Ok,thanks again, great job!
  13. Great Job! Can you talk about the process for the...

    Great Job! Can you talk about the process for the face?
  14. Replies
    14
    Views
    884

    What would you prefer to do? Rebuild a slipper...

    What would you prefer to do? Rebuild a slipper maybe seasonally, or throw axles at it possibly everytime you take it out. Kind of the 2 extremes.
  15. The problem folks is its a race to the bottom.We...

    The problem folks is its a race to the bottom.We all want the lowest price and you ultimately sacrifice so much.
    1 LHS, 3 USED Craigslist/FB. Parts LHS 1st
    I'm fearful LHS,are going to go the way...
  16. Replies
    12
    Views
    803

    100% what he said^^^^^

    100% what he said^^^^^
  17. Replies
    10
    Views
    366

    This is/was my point. Thanks for the help...

    This is/was my point.

    Thanks for the help fellas! I looked up the Stampede gearing, great idea,btw! To get back to "stock" all around basher mode. I need to change my pinion to 11.
  18. Replies
    14
    Views
    785

    I'm interested to say the least....

    I'm interested to say the least....
  19. Replies
    10
    Views
    366

    Yes, from automotive speak, you would change from...

    Yes, from automotive speak, you would change from a stock rear end of 3.73 to a 4.11 for bigger tires
  20. Replies
    10
    Views
    366

    Don't bigger 2.8 tires cause the motor to work...

    Don't bigger 2.8 tires cause the motor to work harder, resulting in excessive heat.

    It just seems to me that you should change gearing to accommodate the larger tires.
  21. Replies
    10
    Views
    366

    Maintain stock ratio with 2.8 tires

    I tried the search function but not entirely sure what to search for. I'm running to 2.8 trenchers on 2 s. What gearing do I need to run to maintain the 13 / 54 stock ratio. Thanks folks
  22. Replies
    14
    Views
    477

    Duct tape can be miserable to take off after a...

    Duct tape can be miserable to take off after a day or two. Any masking tape is fine.
  23. Replies
    11
    Views
    580

    Sure, what did use? Plz, update us after a few...

    Sure, what did use? Plz, update us after a few months of use!
  24. Not proud of it, but either myself or my son has...

    Not proud of it, but either myself or my son has broke one. But, I agree with your post. You need to engineer in weak links. Something is going to break.
  25. Cool vid,cool idea

    Cool vid,cool idea
Results 1 to 25 of 154
Page 1 of 7 1 2 3 4