Search:

Type: Posts; User: Steve g

Page 1 of 14 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    116

    The rated amps of that esc's bec is 6, while the...

    The rated amps of that esc's bec is 6, while the promodeler draws just over 6 at 7.4v. It would be best to get an external bec for it. Even at 6v, it draws 5.5, which is close to the esc's limit. It...
  2. Replies
    2
    Views
    47

    No, the sensors have a hard time keeping up with...

    No, the sensors have a hard time keeping up with the rotor once it starts spinning fast, so you actually lose performance being in sensored only mode. I've read that in a couple places, but there was...
  3. Replies
    13
    Views
    103

    I'd still run a larger system. To me the vxl is...

    I'd still run a larger system. To me the vxl is maxed out on a stock slash or pede. The vxl esc isn't quite enough esc for 3s use. If you go caslte, skip the mamba x and go right for the mamba...
  4. Replies
    19
    Views
    502

    Caslte only had sensored for 4 years? Doesn't...

    Caslte only had sensored for 4 years? Doesn't seem right. Or is it their X line of escs that are 4 years old? Cause I've got sensored motors that are a good 12 years old (not caslte brands). I do...
  5. Replies
    3
    Views
    138

    Yes there are separate profiles you can create...

    Yes there are separate profiles you can create and swap out. Don't think the program card allows for this (I don't use the card ever, so not sure), but the b link does.

    Sent from my SM-G970U...
  6. Thread: Motors

    by Steve g
    Replies
    28
    Views
    397

    Pic doesn't show for me, what is it? Sent from...

    Pic doesn't show for me, what is it?

    Sent from my SM-G970U using Tapatalk
  7. Replies
    4
    Views
    161

    Its a sensorless motor, so it wouldn't work so...

    Its a sensorless motor, so it wouldn't work so well. It will cog while going slow. You'd want a sensored setup for sure, unless you're going to turn it into a basher. Alot of folks on here either run...
  8. Replies
    16
    Views
    533

    Its like a whole new truck now. Looks nice ...

    Its like a whole new truck now. Looks nice

    Sent from my SM-G970U using Tapatalk
  9. Replies
    40
    Views
    979

    I have this same one. Its god awful slow. I would...

    I have this same one. Its god awful slow. I would recommend a powerhd if you need a cheap one. My powerhd 23kg is faster and more powerful then then this one. I believe this is basically a ds3218...
  10. Thread: EVX-2 on LIHV?

    by Steve g
    Replies
    2
    Views
    151

    I run hv 4s on a caslte mmx and on a toro ts150,...

    I run hv 4s on a caslte mmx and on a toro ts150, both of which recognizes them as 4s. Once the caslte thought it was a 5s, I turned it on and off once and it was back at 4s. That was once out of...
  11. Replies
    3
    Views
    198

    If you can get the 272 firmware in that tekin...

    If you can get the 272 firmware in that tekin esc, its the one you want to run. That specific firmware has crawler settings on it that you won't get out of most other escs. The 13.5 will be fine in a...
  12. There was a thread about this about a year ago,...

    There was a thread about this about a year ago, with xmaxx's as the examples. It does make you wonder what is going on. Not sure on the percentage of inproper sticker placement or bad paint lines,...
  13. Replies
    20
    Views
    423

    They both are much larger motors, so I don't...

    They both are much larger motors, so I don't think the 2650 will run hot compared to the smaller 2400kv stock motor. I'd choose the 2650 unless down the road you may try higher voltage then a 4s. The...
  14. Replies
    12
    Views
    448

    I've seen somewhere you mentioned running 12v...

    I've seen somewhere you mentioned running 12v fans. Is that what the turbo fans are? Been looking for 12v fans that aren't cheap brittle computer fans.

    Sent from my SM-G970U using Tapatalk
  15. I agree with the marine grease. I even repack my...

    I agree with the marine grease. I even repack my bearings with it. For your plastic driveshafts, you'll want to use a dry lube, like graphite powder or something like that.

    Sent from my SM-G970U...
  16. Replies
    24
    Views
    631

    Want to add to this by mentioning your tire...

    Want to add to this by mentioning your tire foams. You don't want to get them wet and stay wet, as they will degrade. If they do get wet, take them out of the tires and let them dry. Its a good idea...
  17. Replies
    14
    Views
    449

    https://youtu.be/D4oltPESvhU Watch this, mainly...

    https://youtu.be/D4oltPESvhU
    Watch this, mainly the last half. Hard for us old folks to type. I'm assuming the AS150s are like the XT150s, its why I said what I said.

    Sent from my SM-G970U using...
  18. Replies
    14
    Views
    449

    Get rid of that jumper on the esc side, and plug...

    Get rid of that jumper on the esc side, and plug in a positive of one battery to the negative of the other when you connect to the esc.

    Sent from my SM-G970U using Tapatalk
  19. Replies
    37
    Views
    7,618

    Yes. Larger lower kv motor and a 4s capable esc...

    Yes. Larger lower kv motor and a 4s capable esc (1/8th scale power) is what you want.

    Sent from my SM-G970U using Tapatalk
  20. Replies
    6
    Views
    327

    I'd swap for the badlands. Not a big fan of...

    I'd swap for the badlands. Not a big fan of trenchers myself. Seem good for a skate part, but not real off-road conditions. Do they make the badlands belted in the x maxx size? Although the added...
  21. Just wanted to add on what others said, clean the...

    Just wanted to add on what others said, clean the grub screw and pinion before adding loctite. A quick spray of brake cleaner or motor cleaner will remove any oil residue and help the loctite bond...
  22. I run mainly on grass and gravel, and wasn't...

    I run mainly on grass and gravel, and wasn't impressed with the trenchers. Especially in wet grass, with some leaves like in the fall, they were like driving on ice. Then I bought the badlands, and...
  23. Replies
    8
    Views
    297

    Your reading is accurate, and you still can gain...

    Your reading is accurate, and you still can gain efficiency with the 3800kv, by gearing down quite a bit. 2s to 3s is a 50 percent increase in voltage, so on paper you'd need 50 percent drop in fdr....
  24. Replies
    51
    Views
    1,135

    Where are you storing your lipos before use? You...

    Where are you storing your lipos before use? You do not want them below room temperature before use. Cold lipos will drastically cut your run times.
    As for a new esc, personally I mostly use the c...
  25. Thread: Motor cleaning

    by Steve g
    Replies
    14
    Views
    549

    Yeah it'll work, but as you mentioned its a...

    Yeah it'll work, but as you mentioned its a little thick. Something like a 0w15 would be fine, a 10w or higher would ok if its all you had, but not recommended.

    Sent from my SM-G970U using Tapatalk
Results 1 to 25 of 337
Page 1 of 14 1 2 3 4