Search:

yes while they fit when I send my truck after 4-5 jumps the battery disconnects - I am looking for the new ID connectors as well but it seems they only supply them with batteries why I also keep an...

I used these folks to send it to the UK took 5 days to arrive https://ebay.us/QsVHNx

wow I didnt know that - interesting

so far so good - definitely better looking and fit than [edit] - I just wish they would do different colours


*Per Traxxas's request, you are not to mention that body due to it being a copy of a...

they are actually rubbish - from my experience

just finally got round to test it and so far first full pack through the truck - with the 18/50 I GPS'ed it @44mph(non traxxas), telemetry showing 43mph then 182mph ... I wish there was an option to...

I used alcohol, acetone - changed my loctite and studlock (thinking they were potentially out but they werent, used an old pinion to check - worked fine - no binding issues (pinion doesnt heat up)...

and another attempt - this time studlock ... have tried blue and red loctite so far and only got like 5 minutes each run ... lets see what tomorrow brings (again ...) I wish they had a similar system...

thats an interesting Idea I was thinking finding a slightly small grub screw and another that actually screws in reverse - just like servo saver locking on the Kraton 8S so the outer grub screw...

I looked at it myself as I took the 18T off my Kraton8S ... so I got that one but didnt check yet if its fits and saw the video

someone else had this idea and already identified an issue with this


https://youtu.be/OkHslLYSmbg?t=1014

seems like the flat side on the motor isnt deep enough

it was an issue with the shroud fitting ... next one partially broke and I have replaced them both - not an issue since

Had it out today - flat on a pitch to clock its speed offroad - 18/46 - 43mpm as per traxxas telemetry 2.0 including GPS - pinion came lose and when I checked it over one fan was stuck again...

cheers fellas, tested the fans individually, worked fine, checked everything again:
first receiver box one cable not inserted correctly )probably reason for this), put everything together not...

did that already - negative - all spinning freely - you can see one fan trying to spin on an interval level like every X seconds but thats it really ... might just connect with my LHS to see if I can...

Stock ESC and motor - I am talking about the Velineon dual motor fan - ESC fan is fine

Noticed that my motor fans are not spinning all the time - I was wondering if they dont run all the time as one seems to kick in on intervals well it seems like it wants to start but doesnt so not...

an HR 46T spur

After installing the 2.0 I was wondering why it stays on kmh/C so poking around and looking at the forum I found the option but wondered why my local combination isnt available ...

Here in the UK...

As indicated on the plate location E

@EDMaxxED - you gave me enough challenge to pull everything apart again now and I am not sure but it may be that one pin got unseated when I installed the motor as it came flying out when I undid the...

this is how it looks now

https://i.imgur.com/bwHT1BT.jpg
https://imgur.com/bwHT1BT

https://i.imgur.com/EY8m20p.jpg

https://imgur.com/EY8m20p

not available - this was after it stripped; the pinion also came lose but I used the pin method as per manual - then just locked the motor in place making sure it ran smoothly so I doubt it was the...

well I used the included 46T spur and the stock 18T pinion ... tried it earlier, quick speed run but GPS flew off - clocked 40mph at the time ... wanted to see how it performs in the rough ...
...

I stand corrected - yes - still due to run the 18/46 - I got a HR 50T spur here to test as well ... 51 doesnt sound too bad