Search:

Type: Posts; User: Third Coast RC

Page 1 of 6 1 2 3 4

Search: Search took 0.03 seconds.

  1. Sounds like your clutch bell spring is broken,...

    Sounds like your clutch bell spring is broken, Iíd check it and see if it need to be replaced.
    Justin
  2. Replies
    1
    Views
    264

    toe links & push rods

    Hello all,
    I am rebuilding some toe links and push rods for my Revo 3.3. Does any one know the stock center to center length of these parts?
    Many thanks,
    Justin
  3. Replies
    5
    Views
    937

    That it the glow plug wire. It is used to start...

    That it the glow plug wire. It is used to start the engine and is not needed to keep it running. Its an inexpensive piece, only a couple bucks to replace
  4. Replies
    16
    Views
    1,015

    The top pins can be located by removing the rear...

    The top pins can be located by removing the rear body posts
  5. Thread: Reverse

    by Third Coast RC
    Replies
    1
    Views
    202

    I donít believe that there is.

    I donít believe that there is.
  6. Replies
    2
    Views
    1,106

    I am using the same OFNA tank set up you used...

    I am using the same OFNA tank set up you used previously with the tekno race kit. Is the new truggy clunk tank an easy swap? Were any mods required? I have been having some tuning issues with the...
  7. Replies
    1
    Views
    247

    DMack, We use a lap timing system from...

    DMack,
    We use a lap timing system from Robitronic bought at Towerhobbies. while it is probably not best timing system for serious racing, but we enjoy it. you may need to pick up a few extra...
  8. Replies
    4
    Views
    558

    No prob, the folks in these forums have helped me...

    No prob, the folks in these forums have helped me tremendously through the years.

    Pay it forward!
  9. Replies
    4
    Views
    558

    You have put the front differential in upside...

    You have put the front differential in upside down. We've all done that at least once. Good luck!
  10. Replies
    3
    Views
    210

    i will have a chance to look at it later today...

    i will have a chance to look at it later today and ill check the slipper and loosen it a bit.
    thanks everyone for your input,
    justin
  11. Replies
    3
    Views
    210

    burning through rear half shafts

    ive rebuild trans, diff and dbl checked bearings, but am still burning through half shafts. any thoughts?
    thanks and merry Christmas!
    justin
  12. Replies
    6
    Views
    1,118

    I've tried taking out the FWD parts from my...

    I've tried taking out the FWD parts from my slayer to see how it would work. It was kinda like watching a real pro4 race w/o FWD, hard to track straight, liked to spin out and was difficult in the...
  13. Replies
    15
    Views
    220

    wow, thanks for all of the help. ive seen the hpi...

    wow, thanks for all of the help. ive seen the hpi header, but was wondering if it works with the ez-start? i think i have an old t-maxx header, ill give it a go.

    i have an old dynamite pipe...
  14. Replies
    15
    Views
    220

    side throw header

    hello all,

    does anyone know of a side throw header for the revo with the 3.3? i have a pipe i'd like to try and need a suggestion. i'd like to keep the ez-start if possible.

    thanks!
    justin
  15. Replies
    3
    Views
    155

    thanks double G, my owners manual has the...

    thanks double G, my owners manual has the standard gear ratio as 17/37, not 17/39.

    https://traxxas.com/products/models/nitro/59076-1slayerpro4x4?t=support

    j-
  16. Replies
    3
    Views
    155

    Help me identify this part

    Has anyone seen one of these:
    http://tapatalk.imageshack.com/v2/15/01/11/eb656955a2b9cd19083cbd27e8b0aa91.jpg
    It's 39t, it came out of the 2 speed trans and is part of the 2speed gears. I can only...
  17. Replies
    5
    Views
    690

    Was it rubbing on the blue set screw? It can be...

    Was it rubbing on the blue set screw? It can be replaced with a M4 grub screw and should fix the problem.

    Post some pics and we'll be better able to help.

    Good luck!
    Justin
  18. Replies
    2
    Views
    755

    That's it, best upgrade I've put on my truck

    That's it, best upgrade I've put on my truck
  19. Replies
    11
    Views
    2,089

    I was not aware of this disclosure, glad I've...

    I was not aware of this disclosure, glad I've never bought a set. I use the slash offset 12mm rims with taped proline badlands
  20. Replies
    11
    Views
    2,089

    Correct, they bolt right on, well, they use...

    Correct, they bolt right on, well, they use screws...

    It comes with a drill bit for the rims, if they are 5mm and won't fit over larger spindle. That would be the only "mod" needed

    Hope this...
  21. Replies
    11
    Views
    2,089

    I think proline only makes 12mm hex rims now. You...

    I think proline only makes 12mm hex rims now. You will need tra6869 to use 12mm rim on your slayer. There r other mods (tekno), but the traxxas hexes work the best.
    Good luck!
    Justin
  22. I use Traxxas diff oil in my diffs (see link). I...

    I use Traxxas diff oil in my diffs (see link). I use 50k in the front and 30k in the rear.

    http://buy.traxxas.com/product_info.php?products_id=7395

    hope this help!
    Justin
  23. Replies
    2
    Views
    2,344

    I have the XO-1 adapters and love them on my...

    I have the XO-1 adapters and love them on my slayer, really opens up wheel selection (or pre-glued). The part # is TRA6869.
    Good luck!
    Justin
  24. Replies
    4
    Views
    385

    +1 on the rally build, some good ideas

    +1 on the rally build, some good ideas
  25. Replies
    4
    Views
    596

    They are 55mm with the 32mm shock shafts and they...

    They are 55mm with the 32mm shock shafts and they also make 29mm shafts. You will have plenty if adjustment with them.
    Good luck
    Justin
Results 1 to 25 of 132
Page 1 of 6 1 2 3 4