Search:

Type: Posts; User: zedorda

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Thread: Nomad slash

    by zedorda
    Replies
    15
    Views
    156

    It is one awesome looking rig. I think I would...

    It is one awesome looking rig. I think I would still put the Stampede rear bumper on for just something to be there for any cartwheeling that might happen.
  2. Replies
    5
    Views
    54

    If you install the on the correct sides they have...

    If you install the on the correct sides they have stock toe in. If installed on the opposite sides I think it reduces the toe in to 1 degree.
  3. Replies
    18
    Views
    633

    This is an old thread so not likely to get...

    This is an old thread so not likely to get replies from them. You are making a common mistake in understanding how a fan works when right up against a solid surface. This was debated over about 20-30...
  4. Replies
    19
    Views
    1,195

    Thanks much and I agree 6 inch wide body would be...

    Thanks much and I agree 6 inch wide body would be nice but anything I ever found that narrow was always too short in wheelbase or too short in height to meet up with the chassis tub.
  5. Replies
    19
    Views
    1,195

    I have been using E-Maxx bodies since they we...

    I have been using E-Maxx bodies since they we relatively cheap and pre-cut. Just a slight modification to the stock Slash 4x4 body mounts lets it fit. I have afew pics in this thread:...
  6. Thread: Speed run help

    by zedorda
    Replies
    7
    Views
    367

    You can gear that 2650 up alot more before seeing...

    You can gear that 2650 up alot more before seeing much heat. I would go with a 24/50 before even bothering with 4s.
  7. There are more parts but I do know the plastic...

    There are more parts but I do know the plastic center drive shaft and the diffs are big differences. That might need upgrading to VXL parts.
  8. Replies
    27
    Views
    21,320

    It would be better put that the center diff isn't...

    It would be better put that the center diff isn't for most bashers. It makes the bashing alittle more complicated and most bashers just like to plug and play. When properly setup for your vehicle a...
  9. That explanation was golden. Thank you very much....

    That explanation was golden. Thank you very much. I understood this process as calibrating the slipper clutch while also trying to avoid glazing the pads. Good to know the proper term for it now.
  10. Replies
    23
    Views
    1,083

    I am no expert but as far as I know the Velineon...

    I am no expert but as far as I know the Velineon motor can't work with a brushed only esc.
  11. I have been periodically posting on the Leading...

    I have been periodically posting on the Leading Edge Machine Facebook page trying to connect with LEM to get some parts and o-rings. After a few back and forth comments I was redirected to contact...
  12. Thread: Diff-seal mod

    by zedorda
    Replies
    10
    Views
    693

    I wonder if using a dremel and a stone ball...

    I wonder if using a dremel and a stone ball grinding bit would make a better o-ring seat than a drill bit? And if I can cut a latex glove to make a gasket.
  13. I am also very curious about this clutch break-in...

    I am also very curious about this clutch break-in procedure you speak of. Since I have never heard of it in the 40+ years doing RC. This should be interesting.
  14. Thread: TRX4 and sand?

    by zedorda
    Replies
    18
    Views
    278

    The Velineon system has water resistant...

    The Velineon system has water resistant electronics but it is far from mechanically waterproof. Ball bearings can not be a waterproof barrier and the ones in the Velineon motor are not even stainless...
  15. Replies
    4
    Views
    74

    I am not sure there is a maintenance schedule for...

    I am not sure there is a maintenance schedule for the Velineon motor. Most just rebuild when there is a problem with the bearings or it stops working.

    After adding a drip or 2 of oil just work...
  16. With a tight slipper clutch it doesn't affect...

    With a tight slipper clutch it doesn't affect anything because it just acts like its not there. The only problem you get from a tight slipper clutch is damage to other driveline parts like axles,...
  17. The aluminum pads are best used by people who...

    The aluminum pads are best used by people who like their slipper clutch locked down tight most of the time. If you use the slipper clutch for any form of traction control use anything but aluminum...
  18. Replies
    5
    Views
    105

    A Velineon equivalent is the Hobbywing Quicrun...

    A Velineon equivalent is the Hobbywing Quicrun 10BL120 esc. Even tho Overpowerxmaxx seems to want everyone running the max10sct it is an upgrade to a Velineon esc and a good one at that.
  19. True they have been completely unreliable for...

    True they have been completely unreliable for having anything in stock much anymore.
  20. Replies
    16
    Views
    189

    The program cards for Hobbywing esc are optional....

    The program cards for Hobbywing esc are optional. They can also be set manually.

    https://www.youtube.com/watch?v=XWq7pgAa6Cg
  21. Replies
    16
    Views
    189

    Most 1/10th scale esc and motors use 4mm...

    Most 1/10th scale esc and motors use 4mm banana/bullet connectors but Velineon uses 3.5mm.
  22. So this new diff doesn't have a plastic spur gear...

    So this new diff doesn't have a plastic spur gear option at all? I like having the metal diff cup but I rather keep the spur gear plastic.
  23. This new diff doesn't use the same spider gears...

    This new diff doesn't use the same spider gears at all.
  24. Cheapest I could find for a Traxxas Velineon...

    Cheapest I could find for a Traxxas Velineon vxl-3s system on eBay was $60 for the 3351r motor and $75 for the 3355r esc. I admit I am not great at mining eBay but they don't seem much cheaper than...
  25. Replies
    2
    Views
    50

    Not likely, RC Planet had the Deegan but they...

    Not likely, RC Planet had the Deegan but they been sold out for awhile.

    https://www.rcplanet.com/traxxas-ford-fiesta-st-rally-brian-deegan-body-tra7412x/*******isp_rel_prd&isp_ref_pos=3
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4