Search:

Type: Posts; User: Trojan366

Page 1 of 6 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    369

    Are you landing wide open throttle?

    Are you landing wide open throttle?
  2. Are the Tetons able to drive on the lawn without...

    Are the Tetons able to drive on the lawn without overheating? I’d assume even though they are smaller scale the design might give them a leg up there.
  3. 1/16 Slash 4x4 or Latrax Teton for 4 year old

    My daughter is turning four and would like a remote control like mine. Curious if anyone has any input between the 1/16 slash, teton and prerunner. I want something that will grow with her. I'd...
  4. Replies
    4
    Views
    84

    is the gear mesh set properly? If things are too...

    is the gear mesh set properly? If things are too tight it will cause binding.
  5. Replies
    18
    Views
    257

    It already seems like a better radio. I am...

    It already seems like a better radio. I am considering swapping my slash 4x4 over to a spektrum receiver as well!
  6. Replies
    46
    Views
    1,045

    Finally got my steering issue sorted with a new...

    Finally got my steering issue sorted with a new radio and receiver. I also jumped to a 31t pinion. Drove around work for a few minutes and the motor has plenty of power but it seems to be getting...
  7. Replies
    18
    Views
    257

    Spent 5 minutes last night installing and binding...

    Spent 5 minutes last night installing and binding the new radio and receiver. I still need to set endpoint and adjust things a bit but the steering goes both ways now. Something in the stock radio...
  8. Replies
    9
    Views
    431

    You can get a brand new set of all 4 shocks and...

    You can get a brand new set of all 4 shocks and springs filled with oil on eBay for less than $20 shipped. Might be worth it to have some spares around.
  9. Looks mint. Run it.

    Looks mint. Run it.
  10. Replies
    18
    Views
    257

    Ordered a dx5c and receiver. Probably not a bad...

    Ordered a dx5c and receiver. Probably not a bad idea for range purposes but should help solve or at least narrow down my issue.
  11. Replies
    28
    Views
    796

    Springs made a huge difference! The front end is...

    Springs made a huge difference! The front end is much more planted and will actually steers under part throttle. I have a bit more adjusting to do but if anyone is looking to run GTR shocks on the...
  12. Replies
    18
    Views
    257

    I have been leaning towards a Tx/Rx issue because...

    I have been leaning towards a Tx/Rx issue because both servos turns much further in one direction than the other. With nothing attached both the new and old servos did the same thing.
  13. Replies
    18
    Views
    257

    I’m not sure if the drag link is too long or...

    I’m not sure if the drag link is too long or short since I’m not sure how long it should be haha. I was wondering about the tsm. It is a Traxxas tqi transmitter and the appropriate receiver but as...
  14. Replies
    18
    Views
    257

    I have tried the servo horn at 11, 12 and 1...

    I have tried the servo horn at 11, 12 and 1 o’clock positions. Everything in the front end seems to be properly assembled and turns freely when the drag link is removed.
  15. Replies
    18
    Views
    257

    I measured both tie rods and they are within a...

    I measured both tie rods and they are within a couple of mm.
  16. Replies
    18
    Views
    257

    Tried that twice and nothing. I’m stumped.

    Tried that twice and nothing. I’m stumped.
  17. Replies
    18
    Views
    257

    Barely steers left?

    I have done a bunch of reading and can’t figure this one out. My rustler steers too far right and barely turns left. I reset the transmitter. I reset steering endpoints. I replaced the Servo. There...
  18. Replies
    12
    Views
    364

    I know nothing about that motor and esc but if...

    I know nothing about that motor and esc but if they can handle 2s or 3s lipid they would completely change how it drives.
  19. Replies
    12
    Views
    364

    Are you happy with how it runs now? Yes- don’t...

    Are you happy with how it runs now?
    Yes- don’t upgrade
    No- consider upgrading
  20. Thread: Screw Set

    by Trojan366
    Replies
    14
    Views
    302

    I ordered a set of vxl take off screws from eBay...

    I ordered a set of vxl take off screws from eBay and it was pretty complete. I havenít found anything it was missing yet.
  21. Replies
    46
    Views
    1,045

    Almost looks too good. I’m not sure I want to...

    Almost looks too good. I’m not sure I want to risk flipping it over lol. I’ll probably run it tomorrow and see how it feels. This body is a bit wider behind the front wheels than stock. I am hoping...
  22. Replies
    46
    Views
    1,045

    Body is done. Not bad for maybe an hour. I was...

    Body is done. Not bad for maybe an hour. I was planning on masking the “bed” and back window areas but got distracted and forgot. Still pretty happy with how it turned out!...
  23. Replies
    10
    Views
    148

    Higher gearing puts more stress and load on the...

    Higher gearing puts more stress and load on the motor, esc and battery.
  24. Replies
    10
    Views
    148

    yes 32p. I am debating whether to jump to a 31...

    yes 32p. I am debating whether to jump to a 31 or 34t pinion or just got right to mod 1 gearing. Also not sure when the gearing will overload my electronics. I am assuming my 5000mah 3s traxxas...
  25. Replies
    10
    Views
    148

    The motor seems to be handling this 27/50 gearing...

    The motor seems to be handling this 27/50 gearing with ease. I am thinking about jumping up to a 31t pinion. I noticed with the 27t I can barely get the hex in to tighten the motor and set gear...
Results 1 to 25 of 138
Page 1 of 6 1 2 3 4