Search:

Type: Posts; User: rangerfredbob

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Replies
    806
    Views
    77,290

    the bike shock might work fine, if the mount...

    the bike shock might work fine, if the mount point was about an inch or two from the pivot point, even better if you angled the shock way down... you can make it work
  2. Replies
    11
    Views
    436

    yes, they have to be the same frequency range...

    yes, they have to be the same frequency range...
  3. Replies
    41
    Views
    2,685

    for a servo saver, just make your own, just look...

    for a servo saver, just make your own, just look at the proline steering for the Maxx, or something else, it doesn't have to be complicated, just make it something that's solid until you put a bunch...
  4. ok, I know being from guatamala some of the...

    ok, I know being from guatamala some of the language stuff doesn't transfer correctly, but what they're telling you to do is turn the radio on, take the screw that holds the servo saver to the servo...
  5. Replies
    11
    Views
    537

    unless the engine is turning the spur gear past...

    unless the engine is turning the spur gear past idle, the output shaft won't turn, there are clutches involved with reverse that only engage past a certain rpm...
  6. Replies
    3
    Views
    244

    it's just the kind of fuel you use, and doesn't...

    it's just the kind of fuel you use, and doesn't cause any problems...
  7. Replies
    8
    Views
    462

    I've seen it in person where the aluminum body...

    I've seen it in person where the aluminum body post broke the ears off of both rear bulkheads...

    live with them breaking, learn to drive better, lower your body some, or go RPM for something more...
  8. Replies
    4
    Views
    1,260

    if you're still using the stock pipe, take it...

    if you're still using the stock pipe, take it apart and check the inner baffle and other parts, I melted my baffle, and parts of the rest of the pipe... it ran different

    if it changes tone after...
  9. Replies
    9
    Views
    402

    no, it was designed for the pro .15...

    no, it was designed for the pro .15...
  10. Replies
    14
    Views
    551

    use the pipe you have before you go spending more...

    use the pipe you have before you go spending more on a new one, that one should work fine, might not hurt to try something else later though
  11. only problem with the pro .15 is the rear crank...

    only problem with the pro .15 is the rear crank bearing, but that seems to only happen on engines that sit with fuel in them or something similar... I've had 3 rear crank bearings go out on me...
  12. Replies
    16
    Views
    680

    it's not the plug itself, it's the monster...

    it's not the plug itself, it's the monster resistor in the ez start to drop the voltage down to 1.5ish volts...
  13. Replies
    4
    Views
    229

    close, those are the voltage they read when under...

    close, those are the voltage they read when under a load, the no load voltage is a fair amount higher than the with load voltage...
  14. Replies
    5
    Views
    514

    a fairly common cause of this problem is the diff...

    a fairly common cause of this problem is the diff collar breaking at the seam, this will cause the clicking also...
  15. Replies
    44
    Views
    1,267

    I have a hobbico Nexstar that is somewhat DOA at...

    I have a hobbico Nexstar that is somewhat DOA at the moment due to me robbing parts for my new Sukhoi, should be a bit different to fly...
  16. that's not why they last a lot longer, it's...

    that's not why they last a lot longer, it's because plane engines are larger to start with, it's easier to keep the pinch at the top of the stroke and keep compression, not to mention they turn...
  17. Replies
    11
    Views
    595

    try loostening your slipper clutch 1/8 to 1/4...

    try loostening your slipper clutch 1/8 to 1/4 turn and don't pop as many wheelies, that coucd help...
  18. Thread: Zombiez

    by rangerfredbob
    Replies
    6
    Views
    296

    it's most likely a joke, it's too late for me to...

    it's most likely a joke, it's too late for me to come up with any somewhat normal things people use...
  19. Replies
    9
    Views
    664

    that's sweet, but I'd ditch the wing... I know it...

    that's sweet, but I'd ditch the wing... I know it goes with the wrx theme, but looks wrong...
  20. Replies
    4
    Views
    334

    do a search on google for tahuya, it's up in that...

    do a search on google for tahuya, it's up in that area and you should be able to make it most places...

    I'd suggest going with someone that's been there before though, I'm sure if you found the...
  21. Replies
    7
    Views
    394

    get a tranny and appropriate electrics and it'll...

    get a tranny and appropriate electrics and it'll work, you'll just need to come up with some way of mounting the batteries and stuff, oh, and the center shaft yokes are different between the two...
  22. Replies
    2
    Views
    212

    for the maximum force applied to the control...

    for the maximum force applied to the control surfaces(brake or throttle, and maximum deflection(movement), they should be mounted like shown on the first pictures...

    yes, just re center the servo,...
  23. Replies
    13
    Views
    578

    yes, you can get replacement servo cases, tower...

    yes, you can get replacement servo cases, tower or your LHS should be able to get them...
  24. Replies
    6
    Views
    679

    some people pack the diff with silly putty, will...

    some people pack the diff with silly putty, will pretty much lock it up, but will have some give still.

    just think of some stuff that doesn't dry up that is really thick, and that's about it...
  25. Replies
    11
    Views
    439

    yeah, that would do it too :)

    yeah, that would do it too :)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4