Search:

Type: Posts; User: Dakratfink

Page 1 of 15 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    12
    Views
    358

    That’s a very good reason for it to be your...

    That’s a very good reason for it to be your favorite, lol.
    2wd Brushed Slash was what got me back into R/C. It is a great platform.
  2. Replies
    10
    Views
    182

    The two speed transmission is automatic. It...

    The two speed transmission is automatic. It shifts on the fly. It is spring lodes and when it spins up to a certain speed. You can adjust the shift point with a set screw inside the transmission...
  3. Replies
    10
    Views
    182

    I was in the same boat as you a few weeks ago,...

    I was in the same boat as you a few weeks ago, except the T Maxx I acquired was in full running order ( I swapped a Bruahed Slash 4x4 for it. These guys have been very helpful with nitro noob...
  4. Replies
    5
    Views
    120

    Actually, I’m wondering between RPM, or Aluminum....

    Actually, I’m wondering between RPM, or Aluminum. Anyone have any input ?
  5. Replies
    2
    Views
    81

    I don’t know about the LP tires, but I ran the...

    I don’t know about the LP tires, but I ran the “normal” 2.8 trenchers on my old Rustler Vxl . They performed great, but they are a bit heavier than stock. I would use a smaller piŮon with them for...
  6. Replies
    8
    Views
    139

    I was out of RC entirely around the same time(...

    I was out of RC entirely around the same time( later college years ) got back into it a couple of years ago and have been strictly bashing since.
    I like the fast easy power of my Brushless rigs , (...
  7. Note there are lots of other guides out there,...

    Note there are lots of other guides out there, too. If you click on the one above there will probably be at least 1/2 a dozen other links, for similar tutorials. The link above is the one one I used...
  8. https://m.youtube.com/watch?v=Gnq6PQ2nDpg

    https://m.youtube.com/watch?v=Gnq6PQ2nDpg
  9. Replies
    8
    Views
    139

    Is the E Maxx still relevant? I don’t know. But...

    Is the E Maxx still relevant? I don’t know. But even if traxxas stops producing new kits they will probably support parts for a good while.
    I recently picked up an old TMaxx in a trade. Getting...
  10. Replies
    5
    Views
    186

    Little update, When I got back home, I opened up...

    Little update,
    When I got back home, I opened up did cases and shimmed the rear. 2 shims in the back. Didn’t crack open or rebuild the diff because the ring and pinion were in good agape upon...
  11. Replies
    5
    Views
    120

    Not to hijack this thread, but I have a lot of...

    Not to hijack this thread, but I have a lot of slop in my rear wheels. I tried shimming one side with a nylon shin between the drive pin and the bear and there is still a lot of play. Does anyone...
  12. I was looking at this Kinexsis system, too. It...

    I was looking at this Kinexsis system, too. It looks like Horizon has Discontinued it, but the good news is, Horizon, A-Main and Tower all carry the Onyx system which seems to have very similar specs...
  13. Replies
    2
    Views
    38

    There are a lot of possibilities here . It could...

    There are a lot of possibilities here . It could be a bad glow plug.it might be priming.
    This troubleshooting chart is a good place to start. ...
  14. Replies
    1
    Views
    91

    has budget .21 engine that is so inexpensive it...

    has budget .21 engine that is so inexpensive it is almost suspect, but it seems to have good reviews.

    My 2.5 is still low on hours and I’m pretty new to nitro, but if I can find a cheap roller...
  15. Replies
    8
    Views
    182

    I don’t have much experience with upgrading the...

    I don’t have much experience with upgrading the drive train in the 1/16th. I have the stock velineon motor with a Losi ESC in my mini revo and I love it. The stock 380 in the vxl system is pretty...
  16. Replies
    25
    Views
    572

    Yeah,That too

    Yeah,That too
  17. Replies
    25
    Views
    572

    This is getting interesting.

    This is getting interesting.
  18. Replies
    33
    Views
    1,248

    I’ve been scrolling through this post and I can...

    I’ve been scrolling through this post and I can empathize. I’m
    Not in your situation yet, but I’m about 2 years or so I’ll be transitioning from a career in public service to looking for a regular...
  19. Replies
    10
    Views
    182

    I have my recently acquired 2.5T maxx and it is a...

    I have my recently acquired 2.5T maxx and it is a fun truck to play with. I have a lead on another T Maxx classic for cheap, which may be a parts truck, project or a even a runner. However, the...
  20. Replies
    2
    Views
    166

    Oil probably is to a bad place to start. It’s...

    Oil probably is to a bad place to start. It’s amazing how far basic maintenance and lubrication goes on these little machines.
  21. Replies
    34
    Views
    6,693

    Looking forward to some awesome updates.

    Looking forward to some awesome updates.
  22. Replies
    10
    Views
    182

    Looking forward to the build thread. I’ve only...

    Looking forward to the build thread. I’ve only had my 2.5 Maxx for a few weeks, but I’m loving it. I’m hoping to do up a new body and save the original on mine but other than that I don’t feel like...
  23. Replies
    7
    Views
    285

    I canít wait to try this out when I get back to...

    I canít wait to try this out when I get back to Dakota Territory.
    Thank you all so much for the responses. I feel like even though I have been on and off in the hobby for around 30 years I feel...
  24. Thread: Ultimate RC

    by Dakratfink
    Replies
    11
    Views
    696

    I was on FB back around 2008 or so, and dropped...

    I was on FB back around 2008 or so, and dropped it not long after. I hated the intrusive direction it was going even then. Shift now to 10-11 years later and R/C, toys, 1:1 motorcycle and car ,...
  25. I don’t have much of value to input to the thread...

    I don’t have much of value to input to the thread other than just some awe stricken “wow”s
    Since I got Back into R/C a few years ago I have been mostly a basher, but that rig is impressive and...
Results 1 to 25 of 354
Page 1 of 15 1 2 3 4