Search:

Type: Posts; User: MiniSummit50Mph

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    4,456

    High vs Low C rating

    Hello everybody!

    So I recently put the vxl brushless system inside of my mini summit. Before I had a castle 4600kv system in there, but I realized it was to much power when I couldn't get the car...
  2. Replies
    11
    Views
    5,314

    You just have to know your car and what its...

    You just have to know your car and what its limits are. I put a 4600kv castle motor in the mini summit and it worked. It did a backflip off of a jump at full throttle and stripped 1 tooth on the...
  3. Replies
    0
    Views
    1,092

    Merv Rear A arms for Mini summit

    Hello everybody.

    I have the merv dogbones installed on my mini summit. However, the rear two keep popping out. I know that if I purchase the rear a arms for the merv the axles will stop popping...
  4. Please read this thread-important for 1/16 owners

    Goodmorning


    So I recently posted a thread about my esc failing. I sent it to traxxas and they were able to replace it. I plugged the new one in and I had the same issue. The light was flash...
  5. Replies
    6
    Views
    1,942

    Esc has arrived, I will put it in today! ...

    Esc has arrived, I will put it in today! Hopefully it was just a fluke that won't happen again
  6. Replies
    1
    Views
    1,197

    The stock vxl system can't handle 4s or 6s. It...

    The stock vxl system can't handle 4s or 6s. It can only go up to 3s, or two nihm batteries in series for 14.4 volts. I recently upgraded to the vxl system myself and I couldn't be happier. It has a...
  7. Replies
    5
    Views
    1,374

    Thanks! Never really thought about it that way. ...

    Thanks! Never really thought about it that way. That helps alot!
  8. Replies
    6
    Views
    2,097

    I'm not sure how that even happens... I had one...

    I'm not sure how that even happens... I had one servo go on me, and that was my fault. the car flipped and landed on its side and I tried to turn the wheels so the servo stripped and actually...
  9. Replies
    5
    Views
    1,374

    So if i'm using 70c it should be fine?

    So if i'm using 70c it should be fine?
  10. Replies
    5
    Views
    1,374

    C rating???

    Hello everybody!

    Recently i made a thread about esc failure. luckily it was still under warranty and I sent it back to traxxas, and they are sending out a new one!

    once it arrives I would like...
  11. Replies
    6
    Views
    1,942

    No its just a fried esc. I accidentally left a...

    No its just a fried esc. I accidentally left a battery plugged in for a few minutes with the esc turned off. I realized it was plugged in so I un plugged it. I then noticed the esc was extremely...
  12. Replies
    6
    Views
    1,942

    ESC Failure???

    Hello everybody

    Yesterday I ran my mini summit and It worked great. I use a venom 2s battery that is made for 1/16th cars. It is 35c and I had no issues with it. However when i went to run the...
  13. Replies
    6
    Views
    1,456

    I just want to know if there is a fix for this. ...

    I just want to know if there is a fix for this. There seems to be alot of slack in that general area of the car, so maybe some metal stuff would help?

    Thanks!
  14. Replies
    6
    Views
    1,456

    The funny thing is that I've had these axles for...

    The funny thing is that I've had these axles for 3-4 years now and they front ones have NEVER popped out on me once. its only the rear two. Also can the merv arms be used with the long travel...
  15. Replies
    6
    Views
    1,456

    merv cvd driveshaft issue

    Hello everybody

    So I have a mini summit brushless, with the erevo steel cvd's. I noticed that after the brushless upgrade they started to pop out more. Before it had to crash hard or land wrong...
  16. Replies
    2
    Views
    1,951

    quick side note: Finished battery off, lipo...

    quick side note: Finished battery off, lipo cutoff worked perfectly. The only issue I Have so far is the pinion is slipping off the shaft. However, it did go through two crashes before slipping,...
  17. Replies
    2
    Views
    1,951

    Thank you!!!!

    So I just finished the summit. Battery charged, controller and receiver came, motor mounted esc mounted and of the gears meshed. I took it out for a run, and wow! I was popping wheelies without...
  18. Replies
    2
    Views
    1,149

    Thanks, that's really reassuring. The screw is...

    Thanks, that's really reassuring. The screw is actually farther back on the shaft its just that the shaft doesn't come through the pinion. That's definitely great news. Now all I have to wait on is...
  19. Replies
    2
    Views
    1,149

    Castle Motor Shaft Possible Issue

    Hello everybody. Sorry for so many threads recently, but I have just one last question. On the Castle 1406 4600kv the shaft doesn't stick through the pinion like a normal shaft would. WHen i still...
  20. Replies
    3
    Views
    958

    So will any traxxas 2.4ghz transmitter be able to...

    So will any traxxas 2.4ghz transmitter be able to hook up to any traxxas 2.4ghz receiver?

    Thanks
  21. Replies
    3
    Views
    958

    Something Else went wrong....

    So today I got the car all charged up. Plugged it in, turned on the esc, and tried to pair the controller with the esc. Now I have a summit that is 8 years old. It came with a 27mhz AM radio...
  22. Thanks for your reply! THis morning i'm going to...

    Thanks for your reply! THis morning i'm going to charge up the battery and give it its first run being brushless. I hope the 4600kv motor can do alot more than the old titan could lol. I think...
  23. Please Help Answer this Question then I can run my rc again finally after 6 months

    Ok everybody so I finally have everything for the mini summit, motor is all hooked up, charger and battery have arrived, also got a deans connector to solder onto the esc. But I have the castle sv3...
  24. Finishing up Project, Final Questions

    Good afternoon everybody,

    Over the last 6 months I have been working on converting my brushed titan summit to brushless. Before Christmas of last year, I was originally going to upgrade to the...
  25. Thank you for your response! This will...

    Thank you for your response! This will definately help me out with finishing out the mini summit, and then i can move on to other projects that will be just as fun as this one.

    thanks again!
Results 1 to 25 of 82
Page 1 of 4 1 2 3 4