Search:

Type: Posts; User: dgechrgr469

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. The best advice you could get. I painted a car...

    The best advice you could get. I painted a car recently with a translucent metallic red and without seeing the video on the recommended backing colors I used gold and it ended up looking like...
  2. Some paints require a backer, you should spray...

    Some paints require a backer, you should spray this before changing to a different color. To be safe you could let your first color completely dry and mask it off before spraying a second color...
  3. Replies
    39
    Views
    1,106

    Just curious, i thought since you considered a...

    Just curious, i thought since you considered a Nitro Slash why not a Slayer.

    Sent from my VS996 using Tapatalk
  4. Replies
    39
    Views
    1,106

    Did you consider buying a Slayer? I see they too...

    Did you consider buying a Slayer? I see they too are on backorder until the end of December.

    Sent from my VS996 using Tapatalk
  5. Replies
    17
    Views
    396

    Could be RJ Speed RJS1057 Sent from my VS996...

    Could be RJ Speed RJS1057

    Sent from my VS996 using Tapatalk
  6. Thread: T-REX tape

    by dgechrgr469
    Replies
    15
    Views
    650

    Menards is a retail home/building supply center...

    Menards is a retail home/building supply center based in the midwest, similar to Lowes or Home Depot if that helps.

    Sent from my VS996 using Tapatalk
  7. AMain has them for $499.95 Sent from my VS996...

    AMain has them for $499.95

    Sent from my VS996 using Tapatalk
  8. Replies
    22
    Views
    1,029

    If you guys try what i suggested always put the...

    If you guys try what i suggested always put the set screw in the area where the widest part of the pin goes if possible. The pin might bind if it has to rotate in a wider part of the arm/suspension....
  9. Replies
    5
    Views
    407

    I would think these would work better than...

    I would think these would work better than shoulder screws for motion/binding. But then I guess the shock shaft/piston could rotate slightly if the shock body couldn't.

    Sent from my VS996 using...
  10. Replies
    22
    Views
    1,029

    Another idea that works well is grind a flat spot...

    Another idea that works well is grind a flat spot on the shaft and use a set screw through the arm to tighten down on the shaft flat. Losi uses a system like this on their 22SCT front inner pivot...
  11. Replies
    42
    Views
    1,485

    If the springs are a little too long i use the...

    If the springs are a little too long i use the next "softer" pair if you have an assortment.


    Sent from my VS996 using Tapatalk
  12. Replies
    4
    Views
    140

    Also if your shocks are low on oil it will cause...

    Also if your shocks are low on oil it will cause the oil to foam which moves through the piston orifices easier and lessens dampening because of no resistance to piston movement.

    Sent from my...
  13. Replies
    4
    Views
    140

    The shock will not extend unless there is a...

    The shock will not extend unless there is a pressure differential on the piston. Shock extension (or rebound) is mostly spring function. Thick oils or a small orifice opening will increase this...
  14. Replies
    42
    Views
    1,485

    The rear springs will probably work better since...

    The rear springs will probably work better since you are using them on "rear" shocks.

    Sent from my VS996 using Tapatalk
  15. Replies
    42
    Views
    1,485

    I thought so. Sent from my VS996 using Tapatalk

    I thought so.

    Sent from my VS996 using Tapatalk
  16. Replies
    5
    Views
    200

    I agree with the toe out setting for racing on...

    I agree with the toe out setting for racing on 2wd and 4wd. It does help.

    Sent from my VS996 using Tapatalk
  17. Replies
    23
    Views
    504

    I have heard of magnetic body mounts. Did you buy...

    I have heard of magnetic body mounts. Did you buy the truck used?

    Sent from my VS996 using Tapatalk
  18. Replies
    12
    Views
    373

    I'm guessing it's your motor that's overheating?...

    I'm guessing it's your motor that's overheating? If it were my choice i'd go with the sensored motor if i had a sensored esc.

    Sent from my VS996 using Tapatalk
  19. Replies
    5
    Views
    200

    I usually shoot for 1 negative camber and 1 toe...

    I usually shoot for 1 negative camber and 1 toe in. It's personal preference for me. Toe out is to "twitchy" imo and i usually set the front suspension for no bump steer and very little camber...
  20. And your paint job looks very nice! I just did a...

    And your paint job looks very nice! I just did a Monster Fusion with the Pro-line Pearl Lime Green paint. i'm still getting used to air brushing their paint, you really need to just mist on the first...
  21. I've used a high quality thin tape (unsure of the...

    I've used a high quality thin tape (unsure of the brand) that I got from the hobby shop to outline the masked areas then overlapped it with regular masking tape for the remaining areas. I've always...
  22. Replies
    30
    Views
    1,117

    That sucks! For what they cost you think they...

    That sucks! For what they cost you think they would give you a replacement especially in this day and age where news of a unhappy customer travels fast.

    Sent from my VS996 using Tapatalk
  23. Replies
    42
    Views
    1,485

    The correct part numbers for the GTR shocks are...

    The correct part numbers for the GTR shocks are 7461 for blue fronts and 7462 for blue rears. They also have them in green (G suffix) and black (X suffix). There might be red offered also. I know...
  24. Replies
    42
    Views
    1,485

    I have done it, haven't had a chance to run it a...

    I have done it, haven't had a chance to run it a whole lot myself but I haven't heard of anyone having any serious binding problem.

    Sent from my VS996 using Tapatalk
  25. Replies
    23
    Views
    504

    I'm at work but I can look up specs and part...

    I'm at work but I can look up specs and part numbers later unless someone else can help out right now.

    Sent from my VS996 using Tapatalk
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4