Search:

Type: Posts; User: Zat0ichi

Search: Search took 0.01 seconds.

  1. Before needs sound on so you can here when the...

    Before
    needs sound on so you can here when the servo engages

    https://photos.app.goo.gl/jqL7dMR17hNPs667A

    After
    https://photos.app.goo.gl/11jb8CNmshN56nY28
  2. my excessive tightening worked! i flipped and...

    my excessive tightening worked!
    i flipped and cartwheeled it a few times and nothing broke.

    steering is really good now. Not perfect but I'm happy.



    For now.
  3. Replies
    2
    Views
    496

    yeah, integy stiffed me on international postage....

    yeah, integy stiffed me on international postage. I contacted them minutes after ordering because I thought I'd ordered a pair and it was a single. (my own fault) THey then waited 5 days before...
  4. I've not shaved the standoffs. ...

    I've not shaved the standoffs.

    https://imgur.com/djAIgGu

    You can see a bit if copper above the servo saver , that's my home made shim.

    I am being very mean to the plastic (I have ordered a...
  5. I think I have your answer. A fat 2mm shim /...

    I think I have your answer.

    A fat 2mm shim / washer above the servo saver. (i used a few wraps from a paperclip but i'm ghetto like that)

    You then clamp it down hard with the UPPER CHASSIS...
  6. Replies
    4
    Views
    413

    Weakest point, its toast. Done the same thing...

    Weakest point, its toast.
    Done the same thing myself only my rods are not pop free ones.

    https://imgur.com/rdKQJI3

    I wrapped some 24ga wire round super tight until the replacement part...
  7. My biggest issue with the teton. As far as I...

    My biggest issue with the teton.

    As far as I can tell its the spring.1/18th parts are tiny.
    If you buy another steering assembly, make sure it comes with fresh springs.
  8. Cheapest easiest way 1. Pull the springs from...

    Cheapest easiest way

    1. Pull the springs from the shocks.
    2. Savox SAV-SH0262MG drops straight in (had to swap left and right on the controller)
    3. Just take out the front axles and diff.

    You...
  9. Replies
    2
    Views
    444

    Really common problem. Is your steering binding...

    Really common problem.
    Is your steering binding on the servo saver?

    Loosening the chassis screws a tiny bit has help others but not me (the blue plastic that holds the steering assembly in place)...
  10. Replies
    2
    Views
    496

    Can you help me find

    I'm slowly breaking all the plastic parts.

    Currently I'm looking for this (uk/eu stockists)

    https://www.integy.com/st_prod.html?p_prodid=21811#.XwC1GChKh3g

    ball joint just sheared off....
  11. Replies
    11
    Views
    932

    Its the plastic rods and the cups on the end....

    Its the plastic rods and the cups on the end. They rattle on the ball joints.
    The front wheels can move 10 degrees (about) without the servo moving.
  12. Replies
    11
    Views
    932

    All the slop is in rods, I cant see how a new...

    All the slop is in rods, I cant see how a new servo would sort that out.
  13. Replies
    11
    Views
    932

    Not that tough. Forgot to put the truck back in...

    Not that tough. Forgot to put the truck back in training mode and we were at the skate park.
    So the suspension arm kind of snapped after 6ft of air followed by a 15ft drop.
    Also even my son noticed...
  14. Replies
    11
    Views
    932

    Sounds like it's a pretty strong little truck and...

    Sounds like it's a pretty strong little truck and the servo is the part that is most likely to go first.

    Thanks
  15. Replies
    11
    Views
    932

    New to RC - got my son a Teton

    Hi All,

    My son is only 5 but all the other cheap ones he's been bought by grandparents were flawed.

    So I spent a bit more.

    He's loving it in training mode (more batteries on the way) and I...
Results 1 to 15 of 15