Search:

Type: Posts; User: stampedejim

Page 1 of 7 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    6
    Views
    819

    titan 12 t motor

    Does anyone know the RPM and timing on the Titan 12 turn motor?
  2. Replies
    0
    Views
    213

    Traxxas 380 BL

    Does the Traxxas 380 BL have the same mounting screw pattern as a brushed mabuchi 380?
  3. http://www.castlecreations.com/en/sidewinder-sct/s...

    http://www.castlecreations.com/en/sidewinder-sct/sidewinder-sct-waterproof-combo-with-1410-3800kv-motor-sensored-010-0123-02
    A very good motor ESC setup. I have this on mine. Ballistic speed but...
  4. Replies
    11
    Views
    303

    SIDEWINDER SCT WATERPROOF COMBO WITH 1410-3800KV...

    SIDEWINDER SCT WATERPROOF COMBO WITH 1410-3800KV 5MM MOTOR SENSORED
    cut and pasted from castle. I just had my Slash out. It runs like a scared squirrel. I haven't had this much fun since the 70's...
  5. Replies
    11
    Views
    303

    Thank you Grizz, I'm getting stupid in my senior...

    Thank you Grizz, I'm getting stupid in my senior years...Again thank you so much.
  6. Replies
    11
    Views
    303

    As you know, I am completely wrong. In saying...

    As you know, I am completely wrong. In saying that, Will the motor work without the sensor cable installed? It came with a sensor harness but no place to plug it in, in the ESC...I'm on a steep...
  7. Replies
    11
    Views
    303

    I have a castle system, It has no port in the...

    I have a castle system, It has no port in the ESC, Is says to plug into the RX.
  8. Replies
    11
    Views
    303

    Castle compatable reciever

    Can anyone recommend a receiver that has a motor sensor port, that will bind to my Traxxas TX? I'm upgrading to a sensored Castle brushless.
  9. Thread: New 550

    by stampedejim
    Replies
    6
    Views
    486

    New 550

    Just got a new brushed 550 motor for my Slash. Anyone who still appreciates brushed motors have to try one of these. ...
  10. Replies
    18
    Views
    1,220

    Your rear bearing is gone. Particles from this...

    Your rear bearing is gone. Particles from this will make their way into the combustion chamber through the transfer ports and break the platinum coil.
  11. Replies
    0
    Views
    68

    VXL Revo slipper upgrade

    Has anyone upgraded their slipper clutch on their Rustler VXL to a Revo spec assembly? What parts did you use?
  12. Replies
    1
    Views
    135

    Rustler steering bellcranks

    Does anyone know if the latest brushless Rustler has ball bearings in the steering bellcranks?
  13. Replies
    5
    Views
    177

    I've been running 2WD models since the mid 70's,...

    I've been running 2WD models since the mid 70's, I have a smooth throttle sense. My slash 2WD doesn't spin out unless I go hard on the trigger. So, yeah high powered 2WD won't be a problem.
  14. Replies
    5
    Views
    177

    Cool, I have a MERV, Stamp 4X4, Telluride, Slash...

    Cool, I have a MERV, Stamp 4X4, Telluride, Slash and nitro sport, just want something different, I've never driven brushless. What tires are best, I have the same on my nitro sport and on open...
  15. Replies
    5
    Views
    177

    Rustler VXL

    Looking to get a Rustler VLX, will I enjoy it? I want to go quick and just bash. It will be my first brushless model. I will be sticking with 2S
  16. Thread: Diff lock

    by stampedejim
    Replies
    5
    Views
    638

    Diff lock

    What would be the benefit of locking the differential on my Slash?
  17. Brushless

    On the brushless note....I've been running brushed motors since the early 1970s....I want to go brushless, what will I need to give the same performance as a Titan 550 12 turn? I just need the exact...
  18. Replies
    8
    Views
    1,428

    apply 3 volts and run for 15-30 minutes. You can...

    apply 3 volts and run for 15-30 minutes. You can do the break in submersed in a tub of water but don't leave it in too long as the brushes will wear fast.
  19. Replies
    0
    Views
    839

    Slipper clutch

    has anyone tried the slipper clutch with the aluminium pads?
  20. Replies
    12
    Views
    1,035

    I just put a set of big bores on my Slash. Does...

    I just put a set of big bores on my Slash. Does anyone find the oil that comes in them is a little thick?
  21. Replies
    2
    Views
    511

    Brushed motor break in

    Has anyone out there ever used a DC transformer to power new brushed motors for brush break in? I will be breaking in brushed motors a lot, and I am tired of buying dry cells to use.
  22. Replies
    1
    Views
    1,535

    Aluminum shocks

    Are there any good aluminum shocks available for the PreRunner other than the GTR?
  23. Replies
    8
    Views
    520

    Exact same thing. 12 turn 550

    Exact same thing. 12 turn 550
  24. Replies
    8
    Views
    520

    Found one...

    Found one
    https://www.amazon.ca/gp/product/B07D3WDQJZ/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
  25. Replies
    8
    Views
    520

    Brushed motor options for Slash

    What brushed motors has anyone tried on the Slash other than the Titan 12 turn? I tried a 17 turn 540 modified and the armature windings changed color slightly. I'm using a 90 tooth spur and 16 tooth...
Results 1 to 25 of 165
Page 1 of 7 1 2 3 4