Search:

Type: Posts; User: grizzly03

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Someone probably installed an earlier version...

    Someone probably installed an earlier version nitro revo carriers, they used 6x12 bearings.

    You can get bearings that fit them (6x12) or get the carriers that use the bigger 6x13 bearing.
  2. No need. The new ID battery ends will plug into...

    No need. The new ID battery ends will plug into the first generation High Current connector on the ESC.
    Both the new connectors and the old are compatible with each other.


    Traxxas does sell...
  3. Replies
    45
    Views
    1,000

    Looking good. Install the yellow wire on one of...

    Looking good. Install the yellow wire on one of the 4 screws that hold the engine to the motor mount. Best place is one of the 2 on the fuel tank side (under the starter motor). It's the ground for...
  4. Replies
    22
    Views
    385

    LoL. Your an expert at it now!

    LoL. Your an expert at it now!
  5. Replies
    22
    Views
    385

    You got it!:thumbup:

    You got it!:thumbup:
  6. Replies
    22
    Views
    385

    I don't know what you mean about shaft move up...

    I don't know what you mean about shaft move up and down and has play. If you grab the input shaft itself (the shaft that goes into the transmission, not cush-drive parts) it should have a minor...
  7. Are you powering on the servo (radio) and...

    Are you powering on the servo (radio) and centering the trim before installing the servo horn? That's what you should be doing. If you don't center your radio trims and power on the servo before...
  8. Replies
    22
    Views
    385

    You have the metal star piece backwards. Flip it...

    You have the metal star piece backwards. Flip it around, then pull it up into the groove. Then it should look like this. Then install rubber cushion, washer, then the outer half w/3 screws.
    ...
  9. Replies
    4
    Views
    80

    A cracked bulkhead can cause stripped diff gears....

    A cracked bulkhead can cause stripped diff gears. A crack allows the parts (bearings,gears) to flex/move because the rigidness that holds them is compromised. I don't use a set number of shims. Each...
  10. Replies
    5
    Views
    101

    That's how my luck goes also. The glow plug...

    That's how my luck goes also. The glow plug leaking was probably the copper washer (gasket). I've had them deform after being tightened/loosened too many times.

    Maybe check the fuel tank cap is...
  11. Replies
    22
    Views
    385

    I would replace what's broken. The mesh doesn't...

    I would replace what's broken. The mesh doesn't look bad, but that spur gear assembly sliding back and forth is not good. It shouldn't be sliding on the input shaft.
  12. v1 vs v2 info: The v2 has a center diff in it...

    v1 vs v2 info: The v2 has a center diff in it along with metal gears.
  13. Replies
    4
    Views
    80

    The correct way to shim a diff is (by trying and...

    The correct way to shim a diff is (by trying and checking) to remove excess play and not by a predetermined amount of shims. To make it easy put one shim on the ring gear side and see how much play...
  14. Replies
    22
    Views
    385

    I'm going to agree with Live2Fish88 about...

    I'm going to agree with Live2Fish88 about something not right with the cushdrive/spur gear. The spur gear should be out farther (more room between it and blue plate). Check the cross pin is in the...
  15. Replies
    5
    Views
    101

    It's certainly possible. The fuel pickup in the...

    It's certainly possible. The fuel pickup in the tank could have a leak. Do you notice air bubbles in the fuel line when it starts acting up? That would be an indicator. Also check your exhaust for...
  16. Replies
    13
    Views
    253

    It's better to have more available power than not...

    It's better to have more available power than not enough. The ESC and motor will only draw what amps they need from the battery, the battery doesn't push the amp current. Stressing a battery as...
  17. It's not a direct swap. The v2.0 input shaft is...

    It's not a direct swap. The v2.0 input shaft is 6mm where the v1 is 5mm.
  18. Thank you. :thumbup:

    Thank you. :thumbup:
  19. Thread: Dust boots

    by grizzly03
    Replies
    33
    Views
    703

    https://uc5428744230b26bbc92871d1fd0.previews.drop...

    https://uc5428744230b26bbc92871d1fd0.previews.dropboxusercontent.com/p/thumb/AA1WeobZE-B4qoArK-4YHwLbldBs_psy183R4fh-MaFHLEOgqDIBj4Dj-3flx9d0eXdqyN8xnNwmukIgIoslSKFXJjpKW5dBiYb30Fm5lHc4QR6bDMvgsmb_Znl...
  20. I found the same problem with mine. Unfortunately...

    I found the same problem with mine. Unfortunately the new plate is also bent slightly. I think it has to do with the stamping process. I adjusted mine by using gear backlash as a guide to set the...
  21. Thread: Trx4 ifs?

    by grizzly03
    Replies
    17
    Views
    288

    This is what I was talking about, Dana 44 TTB. It...

    This is what I was talking about, Dana 44 TTB. It was 4WD and coil spring suspension. Ford 1980-1996. Basically had a universal joint off one side of the differential.
    ...
  22. The steering servo placement and the receiver box...

    The steering servo placement and the receiver box wire opening direction on the TRX4 really don't help at all. You really need a long lead on any servo you choose. I turned my receiver box around for...
  23. Best comment I've read in a long time! :thumbup:

    Best comment I've read in a long time! :thumbup:
  24. Flux, Have you tested out TSM with that servo? I...

    Flux, Have you tested out TSM with that servo? I might end up with that servo instead of getting another DS470BLHV.
  25. Highly impressed. Feels and works like a quality...

    Highly impressed. Feels and works like a quality piece. When they start making them again I'm getting another for my Erevo 2.0

    They only negative I can say, is I needed a servo extension wire to...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4