Search:

Type: Posts; User: waqrrr

Page 1 of 11 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    12
    Views
    1,913

    Just got an opportunity to buy a Werks 7 Pro,...

    Just got an opportunity to buy a Werks 7 Pro, will this fit with the Traxxas big bore kit? Also, can I use a bump box?
  2. Replies
    12
    Views
    1,913

    Thanks for all good replies! Man, that OS 21TM is...

    Thanks for all good replies! Man, that OS 21TM is expensive (279,99 USD!!!!!) but it sure looks nice. Might have to pick one up anyway :)
  3. Replies
    8
    Views
    1,804

    Ok, thanks! Just noticed that my rear bearing...

    Ok, thanks!

    Just noticed that my rear bearing was shot so I will replace this.
  4. Replies
    1
    Views
    231

    O-rings for TRX 3,3 carb

    Hi!

    I noticed that there are two o-rings where the carb gets attached to the engine. One is sitting in the crankcase itself and one on the carb body. I though both these were 13x1mm but when...
  5. Replies
    12
    Views
    1,913

    So if buying a .21 engine it will fit but if...

    So if buying a .21 engine it will fit but if going .28 then I need the Traxxas Big bore kit?
  6. Replies
    12
    Views
    1,913

    New engine - will it fit?

    Thinking about getting a new engine for my Revo. Will any 21-28 motor fit? How do I know which motormounts I might need?
  7. Replies
    8
    Views
    1,804

    Just read this in another post: "I have had...

    Just read this in another post:

    "I have had this problem with my tmaxx and also my buddies rustler. What both of my problems were was the black plastic nipple under the hsp that your fuel line...
  8. Replies
    2
    Views
    370

    Revo long travel kit for E-Revo

    Will these fit the E-Revo aswell?

    https://uploads.tapatalk-cdn.com/20180313/db7f1a14ddb88e5bf14cd224220a8832.jpg
  9. Replies
    8
    Views
    1,804

    Forgot to mention but it is also very hard to...

    Forgot to mention but it is also very hard to prime.
  10. Replies
    8
    Views
    1,804

    Problems with Revo 3.3

    Hi!

    I just bought a second hand Revo 3.3 and I am having some problems get it up and running properly. Needle settings are as follow:

    - Idle screw set to give 1mm gap in carb
    - LSN is approx...
  11. Replies
    130
    Views
    45,444

    Sticky: Took some video when my friend was out bashing...

    Took some video when my friend was out bashing his Traxxas xMAXX a couple a weeks afgo. As you can see in the video the snow was very heavy so the XMAXX must have gained a few pounds in weight after...
  12. Replies
    3
    Views
    912

    Set failsafe Traxxas TQ 2,4 Ghz

    I tried to set the failsafe on my old TQ 2,4Ghz radio but despite trying many times I can`t get the car to stop when turning off the radio (simulation a radio failure/interference) What happens is...
  13. Replies
    517
    Views
    232,795

    Sticky: Found a nice bashing site for the Slash to play...

    Found a nice bashing site for the Slash to play around in. The gravel was however very loose so it was tough for the Traxxas Slash to get through but it managed alright I think. Always fun just to do...
  14. Replies
    517
    Views
    232,795

    Sticky: Shredding some old tires with the Slash 4x4 :) ...

    Shredding some old tires with the Slash 4x4 :)


    http://www.youtube.com/watch?v=Y1d4pFg3VwE
  15. Replies
    517
    Views
    232,795

    Sticky: Having some fun in the garage with the Slash 4x4...

    Having some fun in the garage with the Slash 4x4


    http://www.youtube.com/watch?v=1emGBA8meWg
  16. Replies
    517
    Views
    232,795

    Sticky: Just bashing around. Love my Slash :) ...

    Just bashing around. Love my Slash :)


    http://www.youtube.com/watch?v=FHnm5nXBqz4
  17. Thread: MIP Wheel nuts

    by waqrrr
    Replies
    3
    Views
    434

    I already have a set of the HR adapters but the...

    I already have a set of the HR adapters but the fitment of these inside my wheels are terrible. MIP have a much tighter fit. See below thread:
    ...
  18. Replies
    19
    Views
    8,396

    Yeah, lets hope so

    Yeah, lets hope so
  19. Thread: MIP Wheel nuts

    by waqrrr
    Replies
    3
    Views
    434

    MIP Wheel nuts

    Stripped the thread in one of my MIP wheel nuts (17mm adapters) and I can`t seem to find them in Sweden so I was wondering if there are any alternative to these wheel nuts or if MIP is the one I need...
  20. Replies
    517
    Views
    232,795

    Sticky: http://www.youtube.com/watch?v=pWm_Rk36Now

    http://www.youtube.com/watch?v=pWm_Rk36Now
  21. Replies
    517
    Views
    232,795

    Sticky: Had a great time in the snow. ...

    Had a great time in the snow.


    http://www.youtube.com/watch?v=Y_xpUfYwIOU&feature=youtu.be
  22. Sticky: Tried 3S with the Castle 5700 motor. Great fun :)...

    Tried 3S with the Castle 5700 motor. Great fun :)

    https://www.youtube.com/watch?v=h3LtXMuta1o
  23. Replies
    517
    Views
    232,795

    Sticky: Had a great time at the beach with the Slash. I...

    Had a great time at the beach with the Slash. I hope you will like the video.


    https://www.youtube.com/watch?v=d3dYTQRA8cE
  24. Replies
    517
    Views
    232,795

    Sticky: Some bashing in the skatepark ...

    Some bashing in the skatepark

    https://www.youtube.com/edit?o=U&video_id=y4qIRxoeITo&feature=vm
  25. Replies
    517
    Views
    232,795

    Sticky: Ice drifting with the Slash: ...

    Ice drifting with the Slash:

    https://youtu.be/S88N5HrPFmk
Results 1 to 25 of 255
Page 1 of 11 1 2 3 4