Search:

Type: Posts; User: CHICAGOMAXX

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. You can get the center colar in aluminum and the...

    You can get the center colar in aluminum and the spacers from UninterRC. I ordered the center colar in black I didn't install it because I made some from scrap metal heavy I know thats all I had.
  2. You can put a MGT 4.0 and under spur gear which...

    You can put a MGT 4.0 and under spur gear which is mod 1 52 toothspur MGT 8.0 spur bearing is to big and will not work. I run the MGT 52t spur on my emaxx 3908 with a 18t pinoin mod 1.
  3. Thread: Upgrading

    by CHICAGOMAXX
    Replies
    1
    Views
    699

    You will probably have to use the emaxx 3908...

    You will probably have to use the emaxx 3908 slipper setup (Can be done with a little cutting at the end of the shaft). Old version will not hold up to brushless power unless you make a strobe...
  4. Were the pictures taken down?

    Were the pictures taken down?
  5. Replies
    7
    Views
    560

    I know you placed an order for a servo already,...

    I know you placed an order for a servo already, I've been looking at this servo for a while JX Servo PDI-HV5932MG 30KG VAS from Aussie RC Playground used it on a Habao MT and it turned those large...
  6. Replies
    13
    Views
    1,539

    Take a look at Gens Ace lipo batteries they can...

    Take a look at Gens Ace lipo batteries they can be had for a good price and are great batteries, there are also other brands which I can't name that I run for an even better price.
  7. Replies
    16
    Views
    1,892

    You could add a Castle bec to provide the proper...

    You could add a Castle bec to provide the proper voltage to your receiver assuming the new esc can handle the combined voltage.
  8. Wow sorry to hear about the up in smoke ESC. I...

    Wow sorry to hear about the up in smoke ESC. I had a Mamba Monster esc go out just before a year of use called Castle and spoke to a representative and explained what it was doing, he asked me what...
  9. Replies
    7
    Views
    496

    Looking good TwoRustyMaxxed! How's it working for...

    Looking good TwoRustyMaxxed! How's it working for you, any other mods. Same body I have on my emaxx. Do those tires ballon a lot and how do you like then. Nice spot for the led lights. What steel...
  10. Replies
    4
    Views
    501

    The unbalanced tires will cause premature bearing...

    The unbalanced tires will cause premature bearing failure, but I think your short run times may be due to the brushed motors. I did have good run time with lipo batteries and a dewalt drill motor...
  11. Wanted to know what you mean by "slider"?

    Wanted to know what you mean by "slider"?
  12. Replies
    3
    Views
    402

    I would try a 18t or 19t that should net you a...

    I would try a 18t or 19t that should net you a good mesh between the two gears a 20t would definitely get you there but I would watch your temps with a 20t.
  13. I would make sure to use the black spring it is...

    I would make sure to use the black spring it is stiffer.
  14. Replies
    2
    Views
    888

    How have thos pins work for you so far? Do you...

    How have thos pins work for you so far? Do you have a link for the pins?
  15. Replies
    2
    Views
    281

    These are what I run . . . and these . . . ...

    These are what I run . . . and these . . .


    Edited for language abuse. If you see a starred out word in your post, you must edit it out to avoid earning warning points; this also applies when a...
  16. Replies
    1
    Views
    205

    No it should be fine. But it wouldn't hurt to get...

    No it should be fine. But it wouldn't hurt to get the new diffs if you do make sure to shim them if needed.
  17. Replies
    2
    Views
    321

    Another option would be to get a center diff that...

    Another option would be to get a center diff that may help with the power being delivered to the diffs that may help stop the breaking of screws, if the slipper is to loose you will melt the spur...
  18. Boast4life you should check for any binding in...

    Boast4life you should check for any binding in your trans and diffs that may be causing the premature wear on your drive cups. I also have the traxxas steel center cvds and for the arms but I do use...
  19. Replies
    7
    Views
    496

    If you are planning on running a brushless system...

    If you are planning on running a brushless system make sure you change the center idler gear to the TRA3996X. I shredded the plastic gear on the second run and change the pin in the top shaft inside...
  20. I don't have any experience with proline servo...

    I don't have any experience with proline servo saver but I hear it's great. You can do the dual servo saver mod with two emaxx servo savers, I did the mod and it works great much better than a single...
  21. Replies
    17
    Views
    867

    I like the way the RCM V-Maxx chassis puts all...

    I like the way the RCM V-Maxx chassis puts all the stock parts in the stock position. The option for the center diff is a plus but I did read that someone bent that chassis with a center diff and a...
  22. Replies
    3
    Views
    258

    Just sent you a PM about a servo. Vas from aussie...

    Just sent you a PM about a servo. Vas from aussie playground has a video of it on a 1/8 monster truck with bigger tires and heavier truck than an E-maxx.
  23. Replies
    10
    Views
    889

    It would be just fine to run the optional spur...

    It would be just fine to run the optional spur gear with out any problems. I run 62t and 65t spur gears with 22t pinion gear, in the hot summer months I run a 65t spur with the same 22t pinion and my...
  24. Replies
    3
    Views
    357

    I have ran 68,65 and 62 tooth spur gears with...

    I have ran 68,65 and 62 tooth spur gears with 19,20,21,22 tooth pinion gears. I like running 22t pinion with 62t spur I like the speed and still has enough wheelie power for me and it seems to break...
  25. To bad you got feed up with the chassis, it would...

    To bad you got feed up with the chassis, it would give you a better handling truck due to the low center of gravity. You could shorten the stubs that come out of the trans case to be able to use the...
Results 1 to 25 of 27
Page 1 of 2 1 2