Search:

Type: Posts; User: Slapjack

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    12
    Views
    401

    Thanks guys

    Thanks guys
  2. Replies
    12
    Views
    401

    I'll figure out which way to do it. But I have...

    I'll figure out which way to do it. But I have another question about my battery... I got the 4s in today and charged it and when it stopped I had 1 cell at about 4.19 and the others were around...
  3. Replies
    12
    Views
    401

    Awesome, thanks

    Awesome, thanks
  4. Replies
    12
    Views
    401

    What do you mean switch from one end to the...

    What do you mean switch from one end to the other? Basically I use one length of wire and solder 1 end to pos and the other end to neg on my female connector right? Can you explain more what I do if...
  5. Replies
    12
    Views
    401

    battery hookup question

    I have a 4S pack and also two 2S packs. right now I have the esc setup with 2 connectors. is it possible to take female connector and solder 1 wire to the pos and the other end of that wire to the...
  6. Replies
    160
    Views
    7,074

    buggybasher... looks good. I was also thinking...

    buggybasher... looks good. I was also thinking about doing the 1717 motor. But I am wondering, can I use the mamba monster 2 instead of the XL2 or extreme? What benefits would the XL2 and extreme...
  7. Thread: Bulk heads

    by Slapjack
    Replies
    30
    Views
    805

    Try contacting FLM directly. That is where I got...

    Try contacting FLM directly. That is where I got mine. fastlanemachine@sbcglobal.net
    I had a email for the lady that does the ordering but I can't find it.
    Buy the Hyper 7 diffs from Dollar Hobby...
  8. Thread: Bulk heads

    by Slapjack
    Replies
    30
    Views
    805

    NFS is right. Go flm and hyper 7 diffs. Just make...

    NFS is right. Go flm and hyper 7 diffs. Just make sure you get hyper 7tq diffs. Hyper 7ss diffs will not fit.
  9. Replies
    2
    Views
    255

    That is literally the exact same spot I broke...

    That is literally the exact same spot I broke mine last fall. I didn't even notice it until I was washing the truck down after doing some jumping. It was on the cold side when mine happened so I...
  10. Replies
    6
    Views
    338

    I figured out why the one wheel was free spinning...

    I figured out why the one wheel was free spinning but then sometimes grabbing and working fine. You can see the left diff gear teeth are rounded and worn down. No teeth snapped or anything like that,...
  11. Replies
    67
    Views
    4,207

    If you don't mind me asking... how much do you...

    If you don't mind me asking... how much do you have into this truck minus electronics (motor/esc/RX/TX)?
  12. Replies
    109
    Views
    7,107

    How much was that cd mount? And what cd did u...

    How much was that cd mount? And what cd did u install in it?
  13. Replies
    109
    Views
    7,107

    I'm liking it brother looks really good. Did u...

    I'm liking it brother looks really good. Did u already have the cd mount? I've been looking for one but can't find one anywhere. I've been wanting to also try the mbx6t shocks but wasn't sure of...
  14. Replies
    6
    Views
    338

    ok... They are both bevel. Thanks.

    ok... They are both bevel. Thanks.
  15. Replies
    6
    Views
    338

    Yea, that is what I figured. Just wanted to ask...

    Yea, that is what I figured. Just wanted to ask before tearing it down. I checked the set screws and they seem to be fine because everything turns and spins when spinning the other wheels. And the...
  16. Replies
    6
    Views
    338

    1:8 diff question

    I have hpi 1:8 trophy buggy diffs in flm hybrids and recently I have noticed that on pavement the truck pulls to one side hard under acceleration. Then last night I noticed that when I hold the truck...
  17. Replies
    3
    Views
    326

    I don't think they still make it. I just saw one...

    I don't think they still make it. I just saw one on eBay and I had never heard of it so I was just wondering.
  18. Replies
    3
    Views
    326

    Flm ice chasis

    Anyone know what the flm ice chasis is? I am assuming it is an older flm version but will it fit the new 3908 eMaxx's?
  19. Replies
    6
    Views
    218

    I tighten mine all the way. I didn't reef on the...

    I tighten mine all the way. I didn't reef on the nut, but its snug. I tried making it a little looser so it wouldn't wheelie as much and twice I melted the spur. What a mess that was! Just use some...
  20. Replies
    6
    Views
    218

    Yea, the metal on metal will make a lot of noise....

    Yea, the metal on metal will make a lot of noise. I have a Kraton that is metal spur and it does sound like a loose chain. I like it though. lol
  21. Thread: Emaxx truggy?

    by Slapjack
    Replies
    35
    Views
    1,350

    I can't recall how the LCG chasis looks...

    I can't recall how the LCG chasis looks underneath but I know when I was going to add the CD mount from centralemaxx I was told I can just drill and mount it to the FLM center skid plate (I have the...
  22. Replies
    8
    Views
    496

    Actually that does make sense. When I checked...

    Actually that does make sense. When I checked them the one did have a slightly higher charge. That must be it. Thank you.
  23. Replies
    8
    Views
    496

    Well it felt like that's what it did....(Still...

    Well it felt like that's what it did....(Still gave me limited power). But maybe it stopped completely then came back on when the battery went back above the 3.5 I had it set to. Just felt different...
  24. Replies
    8
    Views
    496

    Mlx6s vs castle mm2 lvc

    I am wondering if anyone knows the difference between the traxxas branded mm2 in the blue case and the castle version in the black case. I have both and I remember the castle version when the lipo...
  25. Replies
    39
    Views
    1,598

    Ok thanks. Well it would cost me the same to do...

    Ok thanks. Well it would cost me the same to do it either way so I figured I'll do it the way that will last longer ... Thanks
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4