Search:

Type: Posts; User: stampedejim

Page 1 of 6 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    280

    it gets me to 40. Durability is not a concern....

    it gets me to 40. Durability is not a concern. The motor gets 50,000 RPM no load. the stock one gets @ 30,000
  2. Replies
    3
    Views
    158

    Made in Taiwan

    I thought these models were made in Plano TX. It appears they are made in Taiwan???????
  3. Replies
    3
    Views
    280

    $$$$$$$$$$$$$$$$$$ ya can't put anything bigger...

    $$$$$$$$$$$$$$$$$$ ya can't put anything bigger than a 370 in these and expect the ultimate in durability. I put one of these bad boys in my Pre runner, I think I increased my speed to 1/3 more. it...
  4. Replies
    10
    Views
    820

    Update, this motor hauls *****. My Prerunner does...

    Update, this motor hauls *****. My Prerunner does 30 MPH on stock pinion. Now see how long the brushes last.:p~
  5. Replies
    6
    Views
    1,385

    Dude, you talk to sand and water? Woooa!

    Dude, you talk to sand and water? Woooa!
  6. Replies
    5
    Views
    1,467

    allu 6, did you have to modify anything?

    allu 6, did you have to modify anything?
  7. Replies
    10
    Views
    820

    I bought two 370 motors from @bay for $8.00 each....

    I bought two 370 motors from @bay for $8.00 each. They are red, with ball bearings on the motor shaft (still brushed) The motor RPM no load is 50,000. These are going to surpass the stock 370 motor....
  8. Replies
    7
    Views
    659

    The driveline on these models are not engineered...

    The driveline on these models are not engineered to withstand brushless setups. The plastic half shafts are the "fuse" in the driveline to fail, preventing damage to the driveline. If there was a...
  9. Replies
    1
    Views
    294

    Prerunner/LI-Po cutoff?

    Does the esc on the Pre-runner have a Li-Po cut off setting? it doesn't show in the manual.
    Found my answer.
  10. I like the metal diffs/outdrives. It is certainly...

    I like the metal diffs/outdrives. It is certainly a long way from the rally. The drive train on these models will last a long time if you stick with the stock motor. The stock motor needs to have...
  11. Replies
    3
    Views
    1,314

    Are you using 32P gears? This is what I'm using...

    Are you using 32P gears? This is what I'm using and I also went with a 21 T motor.
  12. Replies
    2
    Views
    316

    Ford GT battery

    How long will this model run with a 5800 MAH Li-Po?
  13. Put in a Titan 21 turn motor and a 13 tooth...

    Put in a Titan 21 turn motor and a 13 tooth pinion. I did this and the truck has more climbing power with more manageable speed.
  14. Another way to tell is if you have a light system...

    Another way to tell is if you have a light system on the model, when they dim as you apply throttle, it is time to stop and recharge.
  15. Replies
    25
    Views
    2,015

    Any plastic gear (fibre reinforced nylon) in a...

    Any plastic gear (fibre reinforced nylon) in a drive train, will act like a fuse to avoid damaging more expensive parts of the driveline. It will be cheaper to replace too. Traxxas will probably...
  16. Replies
    22
    Views
    1,093

    If the final drive gear on the portal unit is oil...

    If the final drive gear on the portal unit is oil lite bronze, you do not have to grease it.
  17. Replies
    42
    Views
    1,306

    Flemmish Giant and a Tortoise.

    Flemmish Giant and a Tortoise.
  18. Replies
    11
    Views
    420

    Where is everybody getting the purple and blue...

    Where is everybody getting the purple and blue springs?
  19. Replies
    6
    Views
    213

    Center diff

    What would be the benefit of installing a center diff kit on my Pede.
  20. Replies
    5
    Views
    390

    Found some, $6.00 for ten

    Found some, $6.00 for ten
  21. Replies
    5
    Views
    390

    What bearing kit did you order that had the...

    What bearing kit did you order that had the rocker bearings included?
  22. Replies
    5
    Views
    390

    MERV rocker arm bearings

    Has anyone upgraded the stock bushings to the suspension rocker arms up to the ball bearings? was it worth it?
  23. Replies
    3
    Views
    172

    I've put a Titan 21 turn on mine and it is even...

    I've put a Titan 21 turn on mine and it is even better. A little slower but more climbing torque.
  24. Thread: Ford GT

    by stampedejim
    Replies
    25
    Views
    5,418

    I'm curious how well the fake disk brakes will...

    I'm curious how well the fake disk brakes will hold up when dirt gets between the rotor and caliper. This model is what I dreamed Traxxas would bring out. The R&D the company has done is exquisite....
  25. Thread: Ford GT

    by stampedejim
    Replies
    25
    Views
    5,418

    Yes it will. With the TSM it will drive well.

    Yes it will. With the TSM it will drive well.
Results 1 to 25 of 126
Page 1 of 6 1 2 3 4