Search:

Those arms look much beefier than stock arms. What if you move the pushrods to the middle hole on the arm?

The astroturf track i run at tends to pop those plastic ends out of the balls. Hopefully the thicker tekno plastic ends and bigger balls will work better. Aluminum is never a good upgrade lol. The...

I meant plastic ends, not shock ends sry. I got some v2 plastic ends also to test. Those v2 links would be a great upgrade over v1's, but still not as strong as i would like them to be

But plastic shock ends are much softer than tekno's. The toe link itself is also shorter than stock 3.3's

If you run truetrack you also loose the extended wheelbase other arms offer. The revo truck should be completely redesigned to newer pill standars. The chassis should be extended 19mm to match...

https://i.imgur.com/Q5P6CL1.jpg
https://i.imgur.com/uhxmsCY.jpg
Used part numbers:
- TKR5188
- TKR8052A
- RCAWD F290010

I replaced stock plastic ends with teknos sct410 6.8mm balls and plastic ends. I haven't tried it yet because my 10yo never broken in trx3.3 died, but looks great so far. I will be posting a pic here...

I'm refering to what @olds97_lss said

how did you mount the pipe when installing the rear brace?

Savox 1268 for both steering and throttle (single steering servo) with a lipo pack is best overall combo. I currently run JX Ecoboost cheap HV servos with a lipo and work incredibly great, but that's...

Check slaydens setup and start from there...

Recycled from an older model. It was the hole for the pipe holder i think

No way to get any of those these days. there were a couple on ebay months ago for about 55$. The only one you can get is the OS 11k i think

will get some lc3 and lc4 then. thanks!

After finishing my 10 year gallon today at the track, the 3.3 engine is definitely looking for new sweets. I will be fitting a 1/8th scale air filter and buying some 25% Merlin fuel (what my LHS...

Great! That's all i need. Thank you so much for your help!!

Great, thanks!

Now if any of you can get the measurements for the steel toe link itself i would be very grateful. Maybe i can use some rod ends from the tekno i have instead of the traxxas ones.
...

I would like to keep the possibility to change rear toe-in. Also, aren't rpm true tracks short wheelbase?
It would be nice if you could get some measurements for rear toe link.

Thank you so much!

Hi all!

This weekend i did the first attempt for a track run with my recently track prepared revo.

https://imgur.com/1ofYFEk.jpg

Great success after that much work on the truck. I ran it on...

How having a car prep for bump start would put on an ez-start? A bump start frees up the engine, gets you rid off the crappy one way bearing, much less issues... Send me that starter box lol

That's it. Aluminum rockers may not be bad at all. I would have prefered plastic adjustable rockers but aluminum doens't hurt "anything" but weight.

Aluminum shock ends are not a good upgrade,...

That's what i meant to say. An a-arm should never be aluminum, it's a part, in simple words, made to break. If you change them for aluminum... say goodbye to your chassis. Aluminum gets sloppy with...

What I'm trying to say is, never go aluminum on a part that is made of plastic because it's supposed to break. Revo's driveshafts and transmission are plactic because of $$$$$$$$$$$$$$$$$$$$$. other...

Plastic is best material money can buy on rc world. Only driveshafts, gears and chassis have to be aluminum or steel, in larger scale cars. The revo doesn't benefit at all from steel driveshafts as...

I tested JX high end Coreless servos with great success on a tekno sct410.3, super strong and fast servos. Paired with a lipo they perform really well. the ones that cost 50 bucks or so.

Like you...