Search:

Type: Posts; User: bjoehandley

Page 1 of 20 1 2 3 4

Search: Search took 0.20 seconds.

  1. Lol, yup! That looks about right, it even...

    Lol, yup! That looks about right, it even bounced off and kept going!
  2. Finally got the chance to run a pack through the...

    Finally got the chance to run a pack through the Hoss rear driveshafts and new slipper, very happy with the results!
    ...
  3. Try to pull it apart to see if it looks like mine...

    Try to pull it apart to see if it looks like mine Did, but before taking things apart, hold the spur still while pushing it on a high grip surface. If all the parts in the slipper stay still, but the...
  4. Replies
    10
    Views
    268

    IIRC, the lipos shouldn’t go below 3.7v per cell...

    IIRC, the lipos shouldn’t go below 3.7v per cell and typically max at 4.11v per cell when charged, so I would expect it to start cutting in at about 3.8v.
  5. Replies
    10
    Views
    268

    No problem, good to hear that did it!

    No problem, good to hear that did it!
  6. If it’s not the slipper, it might be the top...

    If it’s not the slipper, it might be the top shaft roll pin, which can break with too much power and grip and not enough slip in the clutch all at once. Here’s the part in question, if that’s the...
  7. Replies
    10
    Views
    268

    Check to make sure the right rear wheel nut isn’t...

    Check to make sure the right rear wheel nut isn’t too tight, that can cause binding with the bronze bushings in the Brushed trucks.
  8. Replies
    38
    Views
    1,452

    That’s what took out the Jato shafts I had on my...

    That’s what took out the Jato shafts I had on my Stampede a few weeks ago, I was doing hard, wheelie inducing pulls from a dig and blasting from asphalt to grass to concrete and back under power (VXL...
  9. Replies
    10
    Views
    260

    Lol, yup, we didn’t even have the internet when I...

    Lol, yup, we didn’t even have the internet when I shot that and that was at least 2 years before either of us joined here!

    BTW, I think this is the camera I took that one with and may still...
  10. Replies
    10
    Views
    260

    Yup, there’s even a Pirahna 1500 NiCd pack,...

    Yup, there’s even a Pirahna 1500 NiCd pack, seriously vintage ProLine rims who’s name I can’t remember, a 16-17 turn Trinity Speed Gem motor, AND that pic was shot on film with one of those Kodak...
  11. Replies
    11
    Views
    419

    I’m using the RPM Arms, the fronts are the XL...

    I’m using the RPM Arms, the fronts are the XL Rustler/Stampede arms while the rears are for the Slash/Stampede 4x4s, as are the rear carriers. Fortunately, I have a lot of adjustment for shocks and...
  12. Well, got my Traxxas Hoss driveshafts and slipper...

    Well, got my Traxxas Hoss driveshafts and slipper rebuild for my Stampede, they fit at the transmission, but donít clear the hollow balls I was using, so I had to use the ones that donít have a...
  13. Replies
    10
    Views
    260

    I try to get the body low enough that the bottom...

    I try to get the body low enough that the bottom of the shell is even with the bottom of the chassis tub....
  14. Replies
    10
    Views
    260

    Or you could buy the Monster Jam/Crainiac/Skully...

    Or you could buy the Monster Jam/Crainiac/Skully body mounts, do the same mods to the rear mounts, then really set the bodies low;)
    ...
  15. Replies
    11
    Views
    419

    The tires are only part of my plan here, I’ve...

    The tires are only part of my plan here, I’ve done what I can to jack the weight forward on the car, that’s why the Rx and ESC are mounted where they are and then I have a 645mg servo that an already...
  16. Replies
    11
    Views
    419

    Thanks RPWJR!

    Thanks RPWJR!
  17. Replies
    11
    Views
    419

    Ok, here it is with the rear wing installed as...

    Ok, here it is with the rear wing installed as well as without that or a body.
    https://hosting.photobucket.com/images/v698/bjoehandley/D68AF9FC_F67D_4E16_A00B_FD6FF2FDE05C_IMG_0784.HEIC...
  18. If the speed is ok, leave it as is, that bigger...

    If the speed is ok, leave it as is, that bigger pinion just makes the truck faster.
  19. Replies
    38
    Views
    1,452

    I may not be able to tell for a couple weeks, but...

    I may not be able to tell for a couple weeks, but I did order a pair of backordered Hoss rear shafts for my 2wd Pede, which has the RPM’s Slash/Stampede 4x4 rear arms and carriers on it already. I...
  20. Replies
    38
    Views
    1,452

    Which holes in the rear carriers are you using...

    Which holes in the rear carriers are you using for the hinge pin? I found with my 2wd Stampede in the early ‘00 that the driveshafts drag on the arms in that spot if using the upper mounting holes...
  21. Sticky: New favorite pic of my Stampede:D...

    New favorite pic of my Stampede:D
    https://hosting.photobucket.com/images/v698/bjoehandley/3F015E50_6016_46E3_8131_8CDD7B90BE6E_IMG_0714.HEIC?width=1920&height=1080&fit=bounds
  22. Finally got the chance to see how my changes...

    Finally got the chance to see how my changes worked, other than losing the wheel nut on the left and likely stripping the center, it did go well and still wheelies when I don’t always want it to!...
  23. Replies
    8
    Views
    847

    Funny running into you here!

    Funny running into you here!
  24. Replies
    51
    Views
    4,302

    Iíve got a few R/C projects to finish first, but...

    Iíve got a few R/C projects to finish first, but I just may look into buying one of these over building a No Prep car from a Bandit like I was thinking about. Looks like it has enough parts on...
  25. Replies
    51
    Views
    4,302

    I’ve got a few R/C projects to finish first, but...

    I’ve got a few R/C projects to finish first, but I just may look into buying one of these over building a No Prep car from a Bandit like I was thinking about. Looks like it has enough parts on...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4