Search:

Type: Posts; User: Scott91370

Page 1 of 10 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thread: Electronics

    by Scott91370
    Replies
    39
    Views
    781

    I'm sure it was just one of those flukes. ...

    I'm sure it was just one of those flukes. Electronics, they either last forever or fail right away. I just happened to get lucky.
  2. Thread: Electronics

    by Scott91370
    Replies
    39
    Views
    781

    Didn't make any progress on this so I call Castle...

    Didn't make any progress on this so I call Castle this morning.
    My Castle Link adapter came in so we connect through that and set everything back to factory. With the sensor wire plugged in the...
  3. Thread: Electronics

    by Scott91370
    Replies
    39
    Views
    781

    Well I was able to walk myself through the...

    Well I was able to walk myself through the programming to make the one change I needed - reverse the motor direction. When I pulled the trigger the truck went backward and when I pushed it the truck...
  4. If it comes like the picture and the motor/esc...

    If it comes like the picture and the motor/esc are good then I see it as being a decent deal.
  5. Replies
    18
    Views
    371

    I don't see any hexes on the hub. Also, lets see...

    I don't see any hexes on the hub. Also, lets see a pic of the nuts you're using and the back of the wheel.
  6. Thread: Electronics

    by Scott91370
    Replies
    39
    Views
    781

    What a whooping this is. Should be so simple but...

    What a whooping this is. Should be so simple but I have to make everything difficult.

    First, I plugged the wire from the esc to the receiver in backwards and nothing would work. So I decided to...
  7. Replies
    220
    Views
    18,081

    I will do! I actually got mine from A Main so it...

    I will do! I actually got mine from A Main so it should be an original.
  8. Thread: Electronics

    by Scott91370
    Replies
    39
    Views
    781

    Saw many of those while shopping around.

    Saw many of those while shopping around.
  9. 1) Yes 2) Yes. Usually the nut will losen up and...

    1) Yes
    2) Yes. Usually the nut will losen up and the wheel comes off a bit letting things round out.
    3) I use these and haven't had the issue since: Traxxas-Blue-Anodized-Aluminum-Flanged-Serrated
  10. Thread: Electronics

    by Scott91370
    Replies
    39
    Views
    781

    From the reading around here it seemed like the...

    From the reading around here it seemed like the best bet for bashing/dirt course and keeping temps low. I just burned up my velineon 2 pole motor and figured if I was replacing it I might as well...
  11. Thread: Electronics

    by Scott91370
    Replies
    39
    Views
    781

    Just clicked ORDER on mine. Man, a whole week! ...

    Just clicked ORDER on mine. Man, a whole week! At least I'll be able to test it before then at slow speed.
  12. Thread: Electronics

    by Scott91370
    Replies
    39
    Views
    781

    It was the blue one. Like I said, it ran for...

    It was the blue one. Like I said, it ran for over a year and never had an issue then two in one day. Not even sure how I bent the second one but the first was a 20ish mph head-on into a curb.
  13. Thread: Electronics

    by Scott91370
    Replies
    39
    Views
    781

    I need to get a drive shaft like the one you have...

    I need to get a drive shaft like the one you have zedorda, what kind is that?
    I bent my first one about a month ago after driving this for over a year. After one session my new one is bent.
    ...
  14. Replies
    36
    Views
    1,683

    This stuff is awesome! I tried to get into 3d...

    This stuff is awesome! I tried to get into 3d printing but me + software = FAIL and I couldn't even figure out how to create a logo to replace the set on the grille and tailgate of my truck. Then I...
  15. Thread: Electronics

    by Scott91370
    Replies
    39
    Views
    781

    I just saw new thread on soldering irons and...

    I just saw new thread on soldering irons and there are some nice setups, I just can't bring myself to spend $90+ for one. I did find a few 60w that say they will go to 896* and come with the wide...
  16. Thread: Electronics

    by Scott91370
    Replies
    39
    Views
    781

    I had to use the case because the Mamba doesn't...

    I had to use the case because the Mamba doesn't have the mounting tabs built on which makes sense since it is after market and not vehicle specific. Not a huge deal, it cam in today, had to trim it...
  17. Thread: Electronics

    by Scott91370
    Replies
    39
    Views
    781

    Finally found the Mamba X & 2650Kv motor from A...

    Finally found the Mamba X & 2650Kv motor from A Main and get them in this morning. Well, kind of. Didn't realize the Mamba wouldn't mount so thanks to Amazon I ordered the mounting kit which was...
  18. I would say pull off the rear wheels and see if...

    I would say pull off the rear wheels and see if the hexes have rounded.
  19. Replies
    220
    Views
    18,081

    Thanks for the info. I bought the 2650Kv. ...

    Thanks for the info. I bought the 2650Kv. Hopefully it will get here tomorrow. I'm ready to have some fun again.
  20. Replies
    17
    Views
    509

    That is a great pic. All those pieces laying...

    That is a great pic. All those pieces laying around waiting for anew home. I can't wait for more pics of the build!!
  21. Replies
    220
    Views
    18,081

    Thanks! I think I am going to pull the trigger...

    Thanks! I think I am going to pull the trigger on it. I know you run the 2400Kv but what is your opinion on the 2650Kv? (I should have asked that in the previous post)

    Thanks for all your help!
  22. Replies
    220
    Views
    18,081

    @El Sob - Is the motor your run (2400Kv) a 1415...

    @El Sob - Is the motor your run (2400Kv) a 1415 size?
    Will the 1512 size fit in a Slash?

    I have found - Castle Creations Monster X 1/8 Brushless Combo w/1512 2650Kv Sensored Motor

    I don't do...
  23. Replies
    6
    Views
    209

    I do not. I'e had rocks in there with and...

    I do not. I'e had rocks in there with and without the cover in place. Easier to clean it out and adjust the slipper if needed.
  24. I would guess misaligned or broken tooth on a...

    I would guess misaligned or broken tooth on a gear.
  25. Thread: Hello all!

    by Scott91370
    Replies
    22
    Views
    400

    Welcome aboard!!! Post up some pics of your toy...

    Welcome aboard!!! Post up some pics of your toy and get ready to spend some more money.
Results 1 to 25 of 235
Page 1 of 10 1 2 3 4