Search:

Type: Posts; User: truggy buggy

Page 1 of 15 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    5
    Views
    485

    this is the receiver connector. what use is it?...

    this is the receiver connector. what use is it?
    http://www.maartenmarchau.be/RC-TrackGent/11406385_10206387810549194_3280924975949102723_o.jpg
  2. Replies
    5
    Views
    485

    TQ 2242 connector in battery tray?

    does anybody know what the connector inside the battery tray is for? and what about the connector on the side of the receiver? i can't find any information on these. not in the manual, not on the net...
  3. Replies
    2
    Views
    279

    well, it looks you changed about everything but...

    well, it looks you changed about everything but the battery ...
  4. Replies
    62
    Views
    2,006

    biggest improvement would be to go brushless...

    biggest improvement would be to go brushless (SCT-3800kv) with 2s lipo (+35C, +5000mah).
    from that point on you'll be starting to break things, which you can upgrade one by one.
    also tires...
  5. Replies
    5
    Views
    447

    yep, they both are velineons.

    yep, they both are velineons.
  6. Replies
    5
    Views
    447

    velineon cogging question

    Same car, same battery, same everything.
    One motor cogs, the other doesn't. what could be the problem?
    Bearings are replaced, so that shouldn't be it ...
  7. Replies
    4
    Views
    720

    hey greatscott, what gearing do you use in the...

    hey greatscott, what gearing do you use in the 2wd slash?
    i'm running a SW3 with 4600kv motor on 16/86 both will switch to the SCT/3800 combo.
    what gearing would be best to have equal speed with...
  8. Replies
    3
    Views
    514

    different velineon sets??

    i have 2 velineon sets, both look like this:
    http://www2.gpmd.com/image/t/trac3349.jpg

    when i look for info on the traxxas site, they seem to look like this:...
  9. Replies
    3
    Views
    366

    thanks to clarify this, and yes i had the CC in...

    thanks to clarify this, and yes i had the CC in mind.
    i guess the 3800kv would be better holding up in the long run.
    or i will switch to the velineon setup, which i guess is about the same as a...
  10. Replies
    3
    Views
    366

    speed and torque comparison

    hello all,

    i've been thinking about the different kv's and the gearing to use with them.

    if i calculated correctly, these should perform about the same:

    3800kv with 23/86 gearing
    4600kv...
  11. Replies
    24
    Views
    892

    sepedajh, if the ESC shuts down, what led(s) ar...

    sepedajh, if the ESC shuts down, what led(s) ar blinking? fast? slow?
  12. Replies
    6
    Views
    354

    yep, direct fit.

    yep, direct fit.
  13. Replies
    36
    Views
    1,098

    need speed? get a 3800kv 550 motor and pump up...

    need speed? get a 3800kv 550 motor and pump up the pinion :)
  14. Replies
    1,126
    Views
    119,859

    busted my ESC ... tried to learn it to swim but...

    busted my ESC ... tried to learn it to swim but it refused :)
  15. since you didn't get any musical tone when you...

    since you didn't get any musical tone when you switched LVD on, the problem HAS to be the motor. it is the motor that emits the tones. and remember to ALWAYS have LVD ON (green light) when you run...
  16. Replies
    11
    Views
    858

    and what motor do you run, Cyclone?

    and what motor do you run, Cyclone?
  17. Replies
    13
    Views
    465

    no leds after it shut off? i would unplug...

    no leds after it shut off?
    i would unplug everything that can be unplugged, then replug, recalibrate and try again.
  18. Replies
    11
    Views
    858

    use zip-ty and waterproof doublesided tape:)

    use zip-ty and waterproof doublesided tape:)
  19. Replies
    13
    Views
    465

    try unplugging the esc from receiver, then turn...

    try unplugging the esc from receiver, then turn everything back on.
    could be a bad connection inside the receiverbox, or even moisture.
  20. Replies
    2
    Views
    247

    make sure the whole drivetrain is moving freely....

    make sure the whole drivetrain is moving freely.
    start from the wheels and bearings, driveshaft, internal gears, ...
    could also be friction inside the gearbox resulting in heat making everything...
  21. Replies
    4
    Views
    677

    motor rotor probably came off the shaft.

    motor rotor probably came off the shaft.
  22. Replies
    11
    Views
    858

    1. SCT combo for 1/10 should be just fine. 16/86...

    1. SCT combo for 1/10 should be just fine. 16/86 should keep temps well down, even 19/86. going any higher (23/86) you should check your temps from time to time, but maybe you should do that anyway...
  23. Replies
    13
    Views
    465

    OK, so what battery are you using? what color...

    OK, so what battery are you using?
    what color is the led when you turn it on?
    could be LVD is set to "on" while you're running a nimh battery.
  24. Replies
    13
    Views
    465

    OK, so what battery are you using? what color...

    OK, so what battery are you using?
    what color is the led when you turn it on?
    could be LVD is set to "on" while you're running a nimh battery.
  25. Replies
    7
    Views
    2,462

    O, but it is running. I plugged the 4-pole 5700kv...

    O, but it is running. I plugged the 4-pole 5700kv in the motiv (SW1) and it runs quite smoothly. Only compared to the same motor on a SW3 it's very meek and tame. The motor can have 100.000 rotations...
Results 1 to 25 of 366
Page 1 of 15 1 2 3 4