Search:

I know there's a second set of holes in the motor mount thing, but not sure what they are for. Thought I read in the manual or somewhere that they are for a larger OD motor. Anyone running a larger...

I don't know. I never used the service.

Replace dl=0 with raw=1 from the dropbox url's, then they will post as images.

https://www.dropbox.com/s/d6lnazj288moabl/SUNP0002.JPG?raw=1

Yep, that's busted alright!

I ran one of those for quite a while on my stampede 4x4, then later on my eJato. Ran in snow quite a bit on the stampede and never had issues. I stopped running it because I wanted to run 3S and they...

Yep. With a bit of ARO on the piston, I was able to push them up through the top without a lot of effort. The "after" photo's was similar.

The difference with the 3 I had done was that the...

It shouldn't come out the top of the sleeve at all really. If it does, it means it's very worn and when the engine heats up, it will be even worse.

These were some I had that I had repinched:...

No, I understood what he was looking for. I know maximizer had the 17mm versions, forgot I had the 14mm versions on my savage at the time.

I too have 4-5 sets of old 3.2" MT tires sitting around...

Never tried anything but traxxas nuts on their hubs. I have 20 of them laying around from cutting the hubs off for the nitro revos so I could use the traxxas hex with an HPI flange nut because the...

If CVD's/bones have well sealed boots, I use grease. If not, I use white lightning chain lube and apply it after every run. Just couple drops on each joint, then it dries for next time. Leaves a wax...

No problem. I've been running tires like that for over a year on my ERBEv2 and outcast on 6S without issue. Lots of WOT backflips and WOT flat out runs. The outcast is geared a bit taller and goes...

Those fans are pretty loud... I ran 3 of them on my 6S trucks for a while, 2 on the motor, 1 on the esc. Well, ones that look like them. They were from rcjuice and badged as hobbystar fans.

I...

I tried tape many many years ago and it worked, until it didn't. Then the tape got balled up inside the tire making it useless and severely out of balance. That was with nitro that ran less than...

With it being cold, they likely aren't gripping that well. I used to run proline road rage tires on my jato and unless it was 75F+ outside and the pavement was hot, they didn't hook up at all.

Guessing he means actual dye. I've seen where people use rit dye. It works with some plastics, just takes time to soak and the water has to be just under boiling I think.

I wrap mine with 500lb cored kevlar cord. Otherwise they blow right off the rims. I didn't do it once with my 3.8 trenchers on my savage flux after switching to 6S and they made it about 2 minutes...

If you buy them, let us know. I wouldn't mind a set of the backflip LP's on 3.8 geodes/revo2.0 wheels to try on my stampede 4x4.

Do you mean just the 1/8th buggy style bead vs the MT/ST style bead? Pretty sure the arrma tires have the 1/8th buggy style bead on them. Hard to tell for sure since every photo I can find of just...

There are 3 cranks that fit the engine. It came with either a bump start pilot crank with standard SG threads (and slide carb), a pull-start threaded crank (and rotary carb) that requires a clutch...

I was overthinking it I guess. :)

I have an old MRC 959 superbrain AC/DC that I use for NiMH stuff. Been using that thing for 10+ years. Works for 1-8 cells with a range of .5-4.5Amps.

When I started lipo, I had the traxxas dual...

I missed that. Not sure why you would run that though. The os carb is really good.

I did try the 3.4 carb on my 3.3, but it kept binding on me no matter how I situated the carb/arm/linkage. I...

Thanks for the refresher. :)

Yep, those weigh 10oz on traxxas 3.8" 17mm geodes vs 13.9oz 3.8 talon ext's from the ERBEv2. Hair bit narrower face as well.

I just weighed one of the 3.8 chevrons on geodes that I have to see. I...

Yeah, they appear to be 13/37 as well... not sure that's as relevant as the OD though.

Carb arm for revo/slayer: https://www.amazon.com/Engines-23818440-Throttle-Lever-Vehicle/dp/B000X4J0SG
Gasket for header: https://www.amazon.com/Engines-21427200-Exhaust-Ring-2-Piece/dp/B000X4KTAO...