Search:

Type: Posts; User: Third Coast RC

Page 1 of 6 1 2 3 4

Search: Search took 0.05 seconds.

  1. 5998 includes the linkage while the other does...

    5998 includes the linkage while the other does not.
    Hope this helps,
    Justin
  2. Replies
    6
    Views
    1,010

    Sounds pretty close. Try to ensure there is no...

    Sounds pretty close. Try to ensure there is no brake engagement at neutral (drag). That will cause excess heat in the brakes and will effect stopping power.
    Have a great weekend!
    Justin
  3. Replies
    6
    Views
    1,010

    I try to adjust the brake “caliper” so that it’s...

    I try to adjust the brake “caliper” so that it’s tight when brakes are applied but has sufficient play when not engaged (.5-1mm). Then I check for all tires for stopping when rolling by hand. I will...
  4. Replies
    6
    Views
    1,010

    The piece that is split is a piece of fuel line....

    The piece that is split is a piece of fuel line. Just cut a new piece and attach. You may need to adjust the brakes to get them to work to your liking.
    Have a great day!
    Justin
  5. Replies
    9
    Views
    484

    Yes, it will bolt right on

    Yes, it will bolt right on
  6. Sounds like your clutch bell spring is broken,...

    Sounds like your clutch bell spring is broken, I’d check it and see if it need to be replaced.
    Justin
  7. Replies
    1
    Views
    348

    toe links & push rods

    Hello all,
    I am rebuilding some toe links and push rods for my Revo 3.3. Does any one know the stock center to center length of these parts?
    Many thanks,
    Justin
  8. Replies
    5
    Views
    1,005

    That it the glow plug wire. It is used to start...

    That it the glow plug wire. It is used to start the engine and is not needed to keep it running. Its an inexpensive piece, only a couple bucks to replace
  9. Replies
    16
    Views
    1,078

    The top pins can be located by removing the rear...

    The top pins can be located by removing the rear body posts
  10. Thread: Reverse

    by Third Coast RC
    Replies
    1
    Views
    286

    I don’t believe that there is.

    I don’t believe that there is.
  11. Replies
    2
    Views
    1,164

    I am using the same OFNA tank set up you used...

    I am using the same OFNA tank set up you used previously with the tekno race kit. Is the new truggy clunk tank an easy swap? Were any mods required? I have been having some tuning issues with the...
  12. Replies
    1
    Views
    274

    DMack, We use a lap timing system from...

    DMack,
    We use a lap timing system from Robitronic bought at Towerhobbies. while it is probably not best timing system for serious racing, but we enjoy it. you may need to pick up a few extra...
  13. Replies
    4
    Views
    687

    No prob, the folks in these forums have helped me...

    No prob, the folks in these forums have helped me tremendously through the years.

    Pay it forward!
  14. Replies
    4
    Views
    687

    You have put the front differential in upside...

    You have put the front differential in upside down. We've all done that at least once. Good luck!
  15. Replies
    3
    Views
    234

    i will have a chance to look at it later today...

    i will have a chance to look at it later today and ill check the slipper and loosen it a bit.
    thanks everyone for your input,
    justin
  16. Replies
    3
    Views
    234

    burning through rear half shafts

    ive rebuild trans, diff and dbl checked bearings, but am still burning through half shafts. any thoughts?
    thanks and merry Christmas!
    justin
  17. Replies
    6
    Views
    1,164

    I've tried taking out the FWD parts from my...

    I've tried taking out the FWD parts from my slayer to see how it would work. It was kinda like watching a real pro4 race w/o FWD, hard to track straight, liked to spin out and was difficult in the...
  18. Replies
    15
    Views
    234

    wow, thanks for all of the help. ive seen the hpi...

    wow, thanks for all of the help. ive seen the hpi header, but was wondering if it works with the ez-start? i think i have an old t-maxx header, ill give it a go.

    i have an old dynamite pipe...
  19. Replies
    15
    Views
    234

    side throw header

    hello all,

    does anyone know of a side throw header for the revo with the 3.3? i have a pipe i'd like to try and need a suggestion. i'd like to keep the ez-start if possible.

    thanks!
    justin
  20. Replies
    3
    Views
    161

    thanks double G, my owners manual has the...

    thanks double G, my owners manual has the standard gear ratio as 17/37, not 17/39.

    https://traxxas.com/products/models/nitro/59076-1slayerpro4x4?t=support

    j-
  21. Replies
    3
    Views
    161

    Help me identify this part

    Has anyone seen one of these:
    http://tapatalk.imageshack.com/v2/15/01/11/eb656955a2b9cd19083cbd27e8b0aa91.jpg
    It's 39t, it came out of the 2 speed trans and is part of the 2speed gears. I can only...
  22. Replies
    5
    Views
    711

    Was it rubbing on the blue set screw? It can be...

    Was it rubbing on the blue set screw? It can be replaced with a M4 grub screw and should fix the problem.

    Post some pics and we'll be better able to help.

    Good luck!
    Justin
  23. Replies
    2
    Views
    1,036

    That's it, best upgrade I've put on my truck

    That's it, best upgrade I've put on my truck
  24. Replies
    11
    Views
    2,746

    I was not aware of this disclosure, glad I've...

    I was not aware of this disclosure, glad I've never bought a set. I use the slash offset 12mm rims with taped proline badlands
  25. Replies
    11
    Views
    2,746

    Correct, they bolt right on, well, they use...

    Correct, they bolt right on, well, they use screws...

    It comes with a drill bit for the rims, if they are 5mm and won't fit over larger spindle. That would be the only "mod" needed

    Hope this...
Results 1 to 25 of 137
Page 1 of 6 1 2 3 4