Search:

Type: Posts; User: stilllearning7

Page 1 of 6 1 2 3 4

Search: Search took 0.02 seconds.

  1. I appreciate all the helpful feedback and...

    I appreciate all the helpful feedback and answers. That does help. My LHS apparently doesn't carry the stub axle for the front drive shaft. They carry the whole drive shaft. Would it be better to...
  2. Replaced stub axle but now wheel is loose (has too much play)

    Hey guys,

    On my 4x4 Slash I broke the stub axle on the front left. Instead of purchasing a new one, I replaced it with a stub axle that used to be on the rear of this same Slash. Now the wheel...
  3. Okay, I apologize that it has taken me so long to...

    Okay, I apologize that it has taken me so long to post the results from testing my battery. Hopefully from my memory and notes, this will be as accurate as possible:

    Results from multi meter:...
  4. I apologize I thought it was 5000 mah but when I...

    I apologize I thought it was 5000 mah but when I looked later I noticed it has 5200 MAH I'm going to try and run the car this evening and drain the battery then check the voltage. I'll charge it back...
  5. Could you recommend a good charger?

    Could you recommend a good charger?
  6. The Mah is 5000.

    The Mah is 5000.
  7. I'm not sure what a lipo Checker is. What I've...

    I'm not sure what a lipo Checker is. What I've checked lipos before was with a regular multimeter to see what the voltages were.
  8. 3s lipo not charging or working right

    Okay guys, I'll try to make this quick and to the point. I tend to be wordy so I'm going to do my best. I have a 3s LiPo SMC battery. I'm not sure how long I've had it. I would say probably at least...
  9. Does it matter what kind of grease to use for the...

    Does it matter what kind of grease to use for the servo gears? Is silicone grease or lithium grease ok for the plastic gears? How much grease do I need to add when replacing gears? I tried to remove...
  10. Is the white lithium grease the best to use for...

    Is the white lithium grease the best to use for the gears?
  11. If the current torque and speed is enough for me...

    If the current torque and speed is enough for me with the stock 2075, would it be worth my time to just order the metal gears and instal them in the 2075? I mean, is this a pretty good servo in...
  12. Can I ask a silly question..... Why is torque...

    Can I ask a silly question..... Why is torque important on the steering servo? Is it in case I use bigger tires? I would think that any of the servos would have enough torque to steer.

    Also,...
  13. r TSX55 TACM0255 Ultra-Torque...

    r

    TSX55 TACM0255
    Ultra-Torque
    Volts Torque Speed
    4.8 181 oz-in (13.1 kg-cm) 0.24 sec/60
    6.0 203 oz-in (14.6 kg-cm) 0.21 sec/60
    Dimensions Weight
    1.6 x 0.8 x 1.5 in
    41 x 20 x 38 mm 2.1 oz
  14. I called my LHS and asked about the 2072X metal...

    I called my LHS and asked about the 2072X metal replacement gears. During the conversation he said that it was a waste of time and recommended the Tactic servo. He said the model number is TACM0255....
  15. Can anyone recommend a better and affordable servo? 4x4 Slash

    I currently have the 2075, but I had to repair it because some teeth were stripped. I'm not sure how that happened. I don't do heavy bashing.
  16. Well oddly enough my servo stripped some teeth. I...

    Well oddly enough my servo stripped some teeth. I thought I could take the 2075 servo off of my 2wd Slash to use only to find that the spectrum receiver was not compatible with the 2075 plug. In...
  17. Slash 4x4 -- What's the best gear pitch to use?

    I'm currently using a 32 pitch pinion and a 32/.08 pitch spur. is there another pitch that's more durable? Also should I use a metal spur? Thanks in advance!
  18. So the aluminum stub axle carriers would last...

    So the aluminum stub axle carriers would last longer than the RPM plastic?:
  19. I installed the MIP axles on the rear. Hopefully...

    I installed the MIP axles on the rear. Hopefully that will hold up. Are jumps the biggest reasons for the A Arms to break?
  20. 4x4 Slash - What parts (that easily break) should be upgraded for durability?

    I broke one of the Rear Stub Axle Carriers today. It was recommended to me to replace it with RPM. What other parts typically break that I should go ahead and buy for the 4x4 Slash? Thanks so much!
  21. So that will mesh well with my stock M .08 54...

    So that will mesh well with my stock M .08 54 tooth spur?
  22. The pinion looks smaller than I thought it would....

    The pinion looks smaller than I thought it would. I know it's two less teeth than my other 15 tooth, but I assumed it would be bigger. I hope it isn't a cheap generic brand that doesn't hold up.
  23. Is brand important with the Pinion Gear? Radient brand??

    I called my LHS, and one thing I was looking for was a 32 Pitch 13 Tooth Pinion for my 4x4 Slash. Apparently they didn't have that size in the Traxxas brand in stock, but they had the Radient brand....
  24. What kind of battery are you running?

    What kind of battery are you running?
  25. Ok, one thing I found out was that apparently...

    Ok, one thing I found out was that apparently before I purchased this Slash, someone installed the 15 Tooth Pinion. I would think that is contributing to my heat. I'm planning to switch that out with...
Results 1 to 25 of 126
Page 1 of 6 1 2 3 4