Search:

Type: Posts; User: gusd2

Page 1 of 3 1 2 3

Search: Search took 0.02 seconds.

  1. Replies
    24
    Views
    817

    Did you bench test the motor? Pull it away from...

    Did you bench test the motor? Pull it away from the spur and carefully spin it up to full speed (wear gloves) to see if it makes the noise while not under any load?

    Sorry, did not see any reply...
  2. Replies
    17
    Views
    2,351

    Oh good, glad it worked for you!

    Oh good, glad it worked for you!
  3. Replies
    80
    Views
    7,059

    Looking forward to the results!

    Looking forward to the results!
  4. Thanks for the advice. I havenít yet tried weight...

    Thanks for the advice. I havenít yet tried weight balancing as shortly after this post I discovered my TSM was not actually working. Fixed that and suddenly the XO1 was tracking 150% better. It...
  5. Replies
    80
    Views
    7,059

    I hear what youíre saying, and yes, these effects...

    I hear what youíre saying, and yes, these effects will be seen in the results. But there is the potential that the app if compared to a GPS sensor reports differently. Ex. On one run this past...
  6. Replies
    80
    Views
    7,059

    The TraxxasLink app does not calculate actual...

    The TraxxasLink app does not calculate actual speed unless you have the GPS module. Otherwise it is a theoretical speed that takes into account all the variables which are fixed, such as spur,...
  7. Replies
    80
    Views
    7,059

    I did some bench tests last night. Started with...

    I did some bench tests last night. Started with the default Traxxas config of 2.846 for Gear Ratio 1 :
    https://uploads.tapatalk-cdn.com/20191121/c9464e4be67a2fdd4bd9646ad18ea2fa.jpg

    The result is...
  8. Replies
    7
    Views
    460

    Yes, it has a screw down cap so you can pretty...

    Yes, it has a screw down cap so you can pretty much tighten it up to the point where it acts as a solid arm ( no servo saver action). Though, why wouldnít you want some protection for the servo?
  9. Replies
    80
    Views
    7,059

    I believe that is because the app is referencing...

    I believe that is because the app is referencing the Drive Ratio Gear 1, which is only the ratio of the diff 37T ring gear and the 13T drive pinion. Itís not the Final Drive Ratio which as per...
  10. Replies
    7
    Views
    460

    Iíve upgraded all of my Slashes to the ST Racing...

    Iíve upgraded all of my Slashes to the ST Racing Aluminum bellcrank. Itís been a solid performer for me.

    ...
  11. Replies
    80
    Views
    7,059

    Itís almost as if the app thinks youíre running a...

    Itís almost as if the app thinks youíre running a transmission with a high and low gear option. Like the Summit. Strange but glad you got it working with your setup.
  12. Replies
    80
    Views
    7,059

    Oh yah, just noticed the same thing. Mine has...

    Oh yah, just noticed the same thing. Mine has only ever referenced Drive Ratio Gear 1.

    My app version is 7.2.0.10671.
    ...
  13. Replies
    80
    Views
    7,059

    Hey ReglarGuy, The gear ratio of the diff and...

    Hey ReglarGuy,

    The gear ratio of the diff and drive shaft pinion, is 2.846, which is the result of dividing 37 (diff gear teeth) by 13 (pinion teeth).

    Are you saying that the Traxxas Link app...
  14. Thread: Tires

    by gusd2
    Replies
    11
    Views
    788

    Itís an Audi, but yah same thing. This was last...

    Itís an Audi, but yah same thing. This was last year and I canít remember the tolerance but I think it was in the 2/32 range. Ended up buying 2 new for the rear axle because the fronts were within...
  15. Replies
    9
    Views
    824

    It works awesome. I use a spare wheel hub and nut...

    It works awesome. I use a spare wheel hub and nut to hold the wheel tight.
  16. Thread: Tires

    by gusd2
    Replies
    11
    Views
    788

    Thatís funny! On my AWD, they wanted me to...

    Thatís funny!

    On my AWD, they wanted me to change all 4, when I got a nail in one and blew out the sidewall.
  17. Replies
    7
    Views
    431

    Itís been a few years since I went from Stampede...

    Itís been a few years since I went from Stampede to Slash 4x4 LCG, but I think you got it covered. From what I recall, everything else (Eg shock towers, diff housings, a arms) are a direct fit.
  18. Thread: Best Ramp 2019?

    by gusd2
    Replies
    15
    Views
    885

    Engineering it to support the weight and force of...

    Engineering it to support the weight and force of a slash doing 30 to 50 mph without deforming will be a interesting problem to overcome. Especially with the added specifications of being light,...
  19. Replies
    5
    Views
    403

    I too have had really good luck with the Titanium...

    I too have had really good luck with the Titanium Nitride stuff. You can get a set of 4 on amazon for $13. Mine are by Neewer and work great.

    Iíve gone through 2 of the Dynamite / Traxxas combo...
  20. Replies
    11
    Views
    539

    +1 If your not racing, the larger can will...

    +1

    If your not racing, the larger can will likely also trend towards running cooler.
  21. Replies
    17
    Views
    830

    Iíve had my slashes for many years now and have...

    Iíve had my slashes for many years now and have moved the shocks to pretty much every hole possible and never had any damage to the shock tower or a-arm holes. At least, no damage that wasnít caused...
  22. Replies
    18
    Views
    993

    I bought a HRB 3s, hardcase from Amazon. It was...

    I bought a HRB 3s, hardcase from Amazon. It was pretty cheap and has lasted a year so far, no issues. Cost at the time was $69 Canadian which is about $53 US.
  23. Thread: Tires

    by gusd2
    Replies
    11
    Views
    788

    Unless youíre gunning for 100mph +, I donít...

    Unless youíre gunning for 100mph +, I donít expect youíre going to see much impact on just replacing the damaged unit.

    Iíve recently been running GRP 1/8 belted tires and have been pretty...
  24. Thread: Tires

    by gusd2
    Replies
    11
    Views
    788

    You should be fine to just replace the damaged...

    You should be fine to just replace the damaged one.
  25. Replies
    11
    Views
    539

    I’m running the Arrma 2400 in my slash, paired to...

    I’m running the Arrma 2400 in my slash, paired to a mamba X. So long as your SC8 has 4mm bullet connectors, the motor will hook right up. The motor itself Runs great and on 3s allows for a larger...
Results 1 to 25 of 72
Page 1 of 3 1 2 3