Search:

Type: Posts; User: tuscani

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    1
    Views
    731

    Revo 3.3 FOC Install Question

    Hey all.. I am finishing up the FOC install. The kit included a screw pin, normal pin and C-Clip. I see the normal pin and clip (I reused existing) are used on the new primary gear and existing shaft...
  2. Replies
    4
    Views
    270

    Figured it out.. it's the RPM Sensor Mount part...

    Figured it out.. it's the RPM Sensor Mount part 6536 :)
  3. Replies
    4
    Views
    270

    What is this and where does it go?

    I removed the engine to rebuild the carb.. what is this piece and does it go between the motor and mount? Or?

    Thanks!

    https://farm2.staticflickr.com/1595/25172232895_7cf095e574_z.jpg
  4. Replies
    0
    Views
    116

    Revo Ready for Halloween

    :)

    Look out kids!


    https://www.youtube.com/watch?v=e55PeL_zB0A
  5. Thanks.. I did try that to no avail.. I even...

    Thanks.. I did try that to no avail.. I even removed the plastic button and tried to push the little black square on the board and when it does go green the truck doesn't move. I think the button on...
  6. VXL-3S Issue.. 1, 2 then 3 blinks and repeat

    Hey all.. I noticed a weird red light pattern on my speed control.. when I plug in the LIPO the green light comes on for a second then I get the following:

    1 red blink
    2 red blinks
    3 red blinks...
  7. Replies
    8
    Views
    389

    Ok.. so both driveshafts spin fine.. when I spin...

    Ok.. so both driveshafts spin fine.. when I spin spur both tires move. When I hold tires spur doesn't move freely. This all sounds like expected behavior.. at a loss. I had this issue even before the...
  8. Replies
    8
    Views
    389

    No power.. video.

    As my Jato warms up it seems to lose power when I accelerate. The clutch and shoes look good and the slipper is fairly tight.. any ideas? Temps are good and I have a nice trail of blue smoke.

    ...
  9. Thread: My Winter Jato

    by tuscani
    Replies
    2
    Views
    447

    My Winter Jato

    Put together some chains and slapped them on a set of Talons! Will post a video soon.

    For those interested.. I used Jack chain.. it runs $0.63 a linear foot. You will need about 12ft to do two...
  10. Replies
    6
    Views
    402

    So I got the clutch bell off and the clutch and...

    So I got the clutch bell off and the clutch and spring are intact.. hmm. I am going to replace the slipper clutch shoes..
  11. Replies
    6
    Views
    402

    NVM... I was able to get the nut off..

    NVM... I was able to get the nut off..
  12. Replies
    6
    Views
    402

    So I got the new MIP clutch today.. but I notice...

    So I got the new MIP clutch today.. but I notice when I try and remove the nut on the spur gear\slipper the shaft just rotates (even when holding the spur gear with my hand) and the nut will not...
  13. Replies
    6
    Views
    402

    Thanks.. I will order up the MIP clutch!

    Thanks.. I will order up the MIP clutch!
  14. Replies
    6
    Views
    402

    Is it the Clutch Shoes?

    The other day my 3.3 Jato stopped moving but the engine rev'd fine when hitting the throttle. Today I took it out and I have to apply the brake or it will go full rev and take off. Does this sound...
  15. Replies
    3
    Views
    624

    cool thx guys

    cool thx guys
  16. Replies
    3
    Views
    983

    VXL Grave Digger Conversion

    What do you guys think? I want to get some red lights here soon.

    http://farm8.staticflickr.com/7185/6902270646_d143f86c6f_z.jpg

    http://farm8.staticflickr.com/7109/7048362765_63e77365fc_z.jpg
    ...
  17. Replies
    3
    Views
    624

    RPM Camber Links

    Quick question on the electric stampede green RPM camber links.. do I need to reuse the pivot balls out of the factory turnbuckles or do I just install the camber links as is? Thanks!
  18. Sticky: http://farm8.staticflickr.com/7185/6902270646_d143...

    http://farm8.staticflickr.com/7185/6902270646_d143f86c6f_z.jpg

    http://farm8.staticflickr.com/7109/7048362765_63e77365fc_z.jpg

    http://farm8.staticflickr.com/7052/6902637386_6cd225a3da_z.jpg
  19. Replies
    1
    Views
    160

    Spur Replacement

    Just replaced the spur gear in my VXL Stampede. Can't remember, tighten down and then loosen half turn?
  20. Replies
    4
    Views
    935

    I heard I need the 5545X horn so I ordered that...

    I heard I need the 5545X horn so I ordered that as well
  21. Replies
    19
    Views
    707

    Ah ok, cool... thanks!

    Ah ok, cool... thanks!
  22. Replies
    19
    Views
    707

    Ok... I assume there is one washer for each bolt?

    Ok... I assume there is one washer for each bolt?
  23. Replies
    4
    Views
    935

    Installing 645MG for Steering

    Hey guys - I am going to be reaplacing my stock steering servo with the 645MG soon. Any FYIs or gotchas I should know about? Is the stock linkage and horn ok?

    Thanks!
  24. Replies
    19
    Views
    707

    I took out the long screws and the mount.. won't...

    I took out the long screws and the mount.. won't be doing that again.. lol. I got the one star washer in, but no luck on the other.

    Nonetheless, the clutch and spring replacement did the trick!
    ...
  25. Replies
    19
    Views
    707

    LHS did not have MIP installed.. so I went with...

    LHS did not have MIP installed.. so I went with stock spring and replaced the shoes as well... where do those two star washers go?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4