Search:

Type: Posts; User: Kw3277

Page 1 of 3 1 2 3

Search: Search took 0.02 seconds.

  1. Replies
    12
    Views
    785

    First of all that is a very good looking truck....

    First of all that is a very good looking truck. Second of all, I run 3s on the extreme heavy duty like HHARIS and have had minimal problems with them. The are cheap and very strong so a good option.
  2. Destroyed my rear bumper and bulkhead and a arms...

    Destroyed my rear bumper and bulkhead and a arms full speed in 3s into an exposed edge of a sidewalk
  3. Thread: Rear end

    by Kw3277
    Replies
    2
    Views
    175

    Oki did that. Now another question....

    Oki did that. Now another question. https://www.hobbytown.com/rpm-traxxas-slash-4x4-front-or-rear-aarms-black-rpm80702/p168358 these a arms say that The upper hinge pin hole of the rear axle carriers...
  4. Replies
    3
    Views
    301

    Are there water resistant fans that do not make...

    Are there water resistant fans that do not make the car not waterproof? And does a fan in addition to a heat sink in the motor make a big difference compared to just a heat sink?
  5. Thread: Rear end

    by Kw3277
    Replies
    2
    Views
    175

    Rear end

    my rear bumper got hit so hard in a roll over in my slash 4x4 that it ripped up the rear end housing completely. The a arm mounts and diff housing all broke. I need to find the complete rear end but...
  6. Replies
    914
    Views
    128,593

    Broke my rear driveshaft on 3s😂

    Broke my rear driveshaft on 3s😂
  7. Thread: slipper

    by Kw3277
    Replies
    11
    Views
    686

    Ok that's probably the difference between my old...

    Ok that's probably the difference between my old and new motor
  8. Thread: slipper

    by Kw3277
    Replies
    11
    Views
    686

    Ok thanks I was worried

    Ok thanks I was worried
  9. Thread: slipper

    by Kw3277
    Replies
    11
    Views
    686

    Is it normal for my .otor to move in like clicks?...

    Is it normal for my .otor to move in like clicks? I bought a new motor and that's what it did. It didn't move smoothly but it clicked. The motor works good but just wondering if something is wrong.
  10. Thread: slipper

    by Kw3277
    Replies
    11
    Views
    686

    Alright thanks

    Alright thanks
  11. Thread: slipper

    by Kw3277
    Replies
    11
    Views
    686

    Any recommendations for upgrades?

    Any recommendations for upgrades?
  12. Thread: slipper

    by Kw3277
    Replies
    11
    Views
    686

    slipper

    So no matter what i do, my clutch always seems to slip. I feel like it's pretty tight I can spin it with my hand but only with decent force. Is this too loose? My car doesn't even try to climb it...
  13. Thread: Please help!!

    by Kw3277
    Replies
    14
    Views
    795

    It did end up being a motor replacement but my...

    It did end up being a motor replacement but my clutch was also toast but it's fixed now
  14. Replies
    1
    Views
    395

    If you have access to a 3d printer it would be...

    If you have access to a 3d printer it would be cheap but not the strongest.
  15. Thread: 60+ mph?

    by Kw3277
    Replies
    28
    Views
    3,435

    I run 13/54 (stock) and have 3s Lipo stock vxl...

    I run 13/54 (stock) and have 3s Lipo stock vxl setup and go 55 top. It gets hot very quick though
  16. Thread: Break in?

    by Kw3277
    Replies
    2
    Views
    337

    Check mesh and set endpoints on servo

    Check mesh and set endpoints on servo
  17. Replies
    41
    Views
    2,747

    With stock motor probably be around 35-40...

    With stock motor probably be around 35-40
    https://traxxas.com/products/models/electric/slash-4x4-ultimate?t=specs
  18. Replies
    41
    Views
    2,747

    to get this clear, you want traxxas brand?

    to get this clear, you want traxxas brand?
  19. If you didn't figure it out mine did the same and...

    If you didn't figure it out mine did the same and took a motor replacement
  20. Replies
    13
    Views
    709

    Now my chArger recognises it I'm just using an ez...

    Now my chArger recognises it I'm just using an ez peak but it will
    start and then flash at 4 amps??
  21. Replies
    13
    Views
    709

    Um so I accidentally left my battery plugged into...

    Um so I accidentally left my battery plugged into my car and left it so it went completely dead. My charger won't recognise it at all!!��
  22. Replies
    41
    Views
    2,747

    I would agree with this. These cars jump far...

    I would agree with this. These cars jump far enough with stock gearing. They also go fast enough...especially on lipos
  23. Replies
    15
    Views
    831

    So i purchased a new motor and instead of turning...

    So i purchased a new motor and instead of turning it kind of clicks even when out of the car even spinning the shaft...it makes weird grinding clicking noise when in the car... There is also Plastic...
  24. Replies
    15
    Views
    831

    So another thought... Is 13/54 gearing stock for...

    So another thought... Is 13/54 gearing stock for a Slash I can't find any charts that include 13/54 as an option
  25. Replies
    15
    Views
    831

    It was purchased second hand and the motor had...

    It was purchased second hand and the motor had obviously been rebuilt and fixed Multiple times. I purchased a new motor and realized how much of a difference that actually made I just want a Way to...
Results 1 to 25 of 65
Page 1 of 3 1 2 3