Search:

Type: Posts; User: Rico116

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Gonna try this and see what it does. Seems...

    Gonna try this and see what it does. Seems interesting. Sure to learn something off of this test.

    VROOOMMMM
  2. I thought of maybe a bad wheel bearing. But you...

    I thought of maybe a bad wheel bearing. But you just described exactly what is going on with the low speed its fine but when going high. Its pulls really hard. So definitely have to check everything...
  3. Thank you for the clarification. I will clean...

    Thank you for the clarification. I will clean them out and see what happens. Not saying I don't believe you, but will definitely inspect some more and see what happens from there. I do have steering...
  4. Thanks Acidic, I could try cleaning and lube it....

    Thanks Acidic, I could try cleaning and lube it. However I go to the other side and do the same action as I did in the last video with caps off the pivot balls and the carrier does return to center...
  5. Thanks Grizz, I tighten to where excess play is...

    Thanks Grizz, I tighten to where excess play is gone, but your comment made me think to look a bit deeper

    So I went back to my truck checked the passenger side found something strange.

    Because...
  6. Steering Locked and a fix?, Pivot Ball Cap Observation

    Greetings, Hope everyone's well.

    I recently found out that when adjusting the pivot ball caps in the front it would mess up the alignment of my steering. When I adjust the caps I tighten as...
  7. Thank you Will call Traxxas, Why this gotta be...

    Thank you Will call Traxxas, Why this gotta be the third defective item, Pulling my hairs out, LOL

    VROOOMMMM
  8. Thanks, done everything even saved a new profile...

    Thanks, done everything even saved a new profile turned off car then back on loaded settings and the transmitter didn't remember the settings but the link app did. Which means the servo is still...
  9. Endpoints not saving sliders not moving traxxas link

    Greetings everyone, hope everyone's well.
    Installed Traxxas Link today and EPA Adjustments are not saving or even moving when adjusting in the app, unless I click reverse and hold the steering wheel...
  10. Thread: Traxxas Link

    by Rico116
    Replies
    3
    Views
    203

    Thanks Justin and Mlmf, Kept everything close and...

    Thanks Justin and Mlmf, Kept everything close and no issues, and followed instructions.

    VROOOMMMM
  11. Thread: Traxxas Link

    by Rico116
    Replies
    3
    Views
    203

    Traxxas Link

    Hope everyone's well.
    Getting Traxxas Link Tomorrow. I am a little bit afraid to do updates. I hear the app forces you to do them and it bricks the car, or messes things all up. Not too sure.
    Can...
  12. Replies
    24
    Views
    537

    Thanks everyone adjusted the end points and the...

    Thanks everyone adjusted the end points and the bellcrank no longer goes all over the place. It returns to center as it should.

    VROOOMMMM
  13. Replies
    24
    Views
    537

    Looks to be the end points are deflecting it out...

    Looks to be the end points are deflecting it out of position. If you look closely at the top of the bellcrank. The screw leading towards the rear of the vehicle you could see it gets pushed up...
  14. Replies
    7
    Views
    422

    I heard of ziptying the wheelie bar in the past...

    I heard of ziptying the wheelie bar in the past that could help. As for the truck rolling over. The E Revo is a very touchy on the steering so if your taking sharp turns your gonna roll over. My...
  15. Replies
    24
    Views
    537

    Will make sure of that. VROOOMMMM

    Will make sure of that.

    VROOOMMMM
  16. Replies
    6
    Views
    217

    I am not sure I didn't fully charge the batteries...

    I am not sure I didn't fully charge the batteries kept it half charged and recalibrated it came back next day esc was fine. Thanks for asking. I be looking for answers , and can't find answers...
  17. Replies
    24
    Views
    537

    Well, I got a few things to look at, Thanks...

    Well, I got a few things to look at, Thanks everyone so far, Will update all of you after doing these things. Hope to get it fixed.

    VROOOMMMM
  18. Replies
    24
    Views
    537

    Now that's interesting. I never thought the specs...

    Now that's interesting. I never thought the specs matter too much but that might be a issue. I don't have a spare servo to test it with. Maybe there's like a way to see determine the appropriate...
  19. Replies
    24
    Views
    537

    I could double check and put car back together...

    I could double check and put car back together and see what it does, and double check everything it won't hurt to check.

    VROOOMMMM
  20. Replies
    24
    Views
    537

    Yes, I have also looked at it when the car was...

    Yes, I have also looked at it when the car was together, and the issue was still present. With no toe links connected.

    VROOOMMMM
  21. Replies
    24
    Views
    537

    2.0 Yes it hits the ends stops, so the force of...

    2.0 Yes it hits the ends stops, so the force of it hitting the end stops knocks it out of the
    center and causes it to stay stuck to the the right? unless you turn it the other way it corrects it...
  22. Replies
    6
    Views
    217

    Thanks, Good to know, Will keep that in mind ...

    Thanks, Good to know, Will keep that in mind

    VROOOMMMM
  23. Replies
    24
    Views
    537

    Thanks Acidic, I like to look where the...

    Thanks Acidic, I like to look where the bellcranks screws into the toe links it doesn't sit perfectly even in the middle watch where it changes back to center around the 17 second...
  24. Replies
    24
    Views
    537

    I never thought of too look at the skid plate ,...

    I never thought of too look at the skid plate , gonna look at that later, Thinking it may be worn like you said. I take a closer look at both pieces.

    Gonna buy a new steering post later just in...
  25. Replies
    24
    Views
    537

    So inspect where the 2 Screws hold the steering...

    So inspect where the 2 Screws hold the steering post down? and look and where the rod inside the bellcrank sits on the post?

    VROOOMMMM
Results 1 to 25 of 306
Page 1 of 13 1 2 3 4