Search:

Type: Posts; User: painter

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    124
    Views
    15,272

    Has problems with Traxxas Stub axle (TRX7753R)...

    Has problems with Traxxas Stub axle (TRX7753R) getting worn out quickly.
    Is there any one that fits 8S in steel?
  2. Replies
    124
    Views
    15,272

    You'll need to contact the manufacturer for...

    You'll need to contact the manufacturer for support for their product.
  3. Replies
    4
    Views
    1,191

    I had the same problem. thought outgoing shaft...

    I had the same problem. thought outgoing shaft was broken, then i contacted Traxxas who sent a new gear set.
    Put everything together again, Someting just spinning around in the servo.
    Hold on for a...
  4. YR 40x40. https://i.imgur.com/O1oBdWR.jpg

    YR 40x40.
    https://i.imgur.com/O1oBdWR.jpg
  5. Replies
    118
    Views
    61,549

    Sticky: Out jumping my X-Maxx-...

    Out jumping my X-Maxx-
    https://i.imgur.com/dPRWq9J.jpg
    https://i.imgur.com/tpQQLno.jpg
    https://i.imgur.com/czlk4Wt.jpg
    https://i.imgur.com/RmXxTkM.jpg
    https://i.imgur.com/9b5fSU9.jpg...
  6. Replies
    2
    Views
    338

    Drive all day on 8 cells with plastic spur. No...

    Drive all day on 8 cells with plastic spur. No problem.
    Max5/ Leopard 1340kv
  7. Thread: Servo....

    by painter
    Replies
    10
    Views
    847

    What do you use for servo horns, Traxxas or...

    What do you use for servo horns, Traxxas or hopups?
  8. Thread: 2085x

    by painter
    Replies
    2
    Views
    409

    Should check this, but want Traxxas original if...

    Should check this, but want Traxxas original if available.
  9. Thread: 2085x

    by painter
    Replies
    2
    Views
    409

    2085x

    Are there any spare parts to buy for the 2085X servo?
    Has managed to round outgoing shaft.
  10. Thread: steering link

    by painter
    Replies
    5
    Views
    495

    Did this today work fine. Can set the length....

    Did this today work fine.
    Can set the length.
    https://i.imgur.com/7PtCIzX.jpg
  11. Thread: steering link

    by painter
    Replies
    5
    Views
    495

    Do you remember what brand rod end is?

    Do you remember what brand rod end is?
  12. Thread: steering link

    by painter
    Replies
    5
    Views
    495

    steering link

    Can you buy only the steering link that comes with 2085X sevo?
  13. Thread: Run times?

    by painter
    Replies
    19
    Views
    1,370

    Ca 15 min WOT run time with 2x5800mah 4 cells...

    Ca 15 min WOT run time with 2x5800mah 4 cells lipo.
    Normal bashing maybe 20 min
  14. Thread: Run times?

    by painter
    Replies
    19
    Views
    1,370

    8 cell all day long.

    8 cell all day long.
  15. Thread: Adjust spring

    by painter
    Replies
    5
    Views
    477

    thank you everyone.

    thank you everyone.
  16. Thread: Adjust spring

    by painter
    Replies
    5
    Views
    477

    Adjust spring

    How far down is the standard measure of the spring. I put 12mm and 50wt oil?
    https://i.imgur.com/p8J2QQh.jpg
  17. Replies
    17
    Views
    1,110

    Something's wrong, my looks like this....

    Something's wrong, my looks like this.
    https://i.imgur.com/mJSSJJP.jpg
    https://i.imgur.com/vFJCDHV.jpg
  18. Keep in mind that the org receiver can not stand...

    Keep in mind that the org receiver can not stand 7.4v before you raise bec. May be the servosaver who needs to be tighten.
  19. Replies
    9
    Views
    592

    Depends on how you drive, but sounds the same as...

    Depends on how you drive, but sounds the same as I get out of 5000mah. Put lipo cutoff at about 3.2-3.4v. 3.0v sounds very low.
  20. Update to the latest software, calibrate esc.

    Update to the latest software, calibrate esc.
  21. Thread: Max5 and???

    by painter
    Replies
    14
    Views
    1,025

    Throw it and run without....

    Throw it and run without.
    https://i.imgur.com/Loc13UX.jpg
  22. Replies
    42
    Views
    1,829

    I just took a pliers and bowed them a bit....

    I just took a pliers and bowed them a bit.
    "Google translate"
  23. Replies
    42
    Views
    1,829

    I did this. https://i.imgur.com/5OVbwiD.jpg

    I did this.
    https://i.imgur.com/5OVbwiD.jpg
  24. Replies
    7
    Views
    701

    This is mine. Look at youtube for info. ...

    This is mine. Look at youtube for info.

    https://www.youtube.com/watch?v=Y_M9K_6Vj6k&t=10s
  25. Replies
    12
    Views
    732

    I like to know to, nead some 8mm pinion.

    I like to know to, nead some 8mm pinion.
Results 1 to 25 of 196
Page 1 of 8 1 2 3 4