Search:

Type: Posts; User: TwoBelugas

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    6
    Views
    149

    Iím sure he will if you are generous enough to...

    Iím sure he will if you are generous enough to supply the replacement parts.:wacko:
  2. Replies
    10
    Views
    608

    Here is the completed product. Looks rather like...

    Here is the completed product. Looks rather like my blue 2wd FLM rustler build, ride height is low since the Hoons tires are the same diameter as grp 1/8 tires, so it will sit higher with buggy tires...
  3. Replies
    63
    Views
    2,937

    Same here. Squeegie donít play when he starts a...

    Same here. Squeegie donít play when he starts a project. :thumbup:
  4. I just don’t think the traxxas cvds were designed...

    I just don’t think the traxxas cvds were designed with 3s and mt tires in mind. They are more for slash 4x4 type use.

    The xo-1 Drive shafts and aluminum bearing carriers are probably the...
  5. The stock rustler 4x4 arms are very good units,...

    The stock rustler 4x4 arms are very good units, they flex more than the older style ones but not as much as the rpm ones.

    Stock arms with tekno m6 should be a very, very durable set up.
  6. Iím partial to the dynamite 1/10 motor fan. Itís...

    Iím partial to the dynamite 1/10 motor fan. Itís not flashy being a plastic case around the 36mm can, but its plastic construction is durable, and comes wired to go on any open channel on the...
  7. From time to time I ím still finding out the...

    From time to time I ím still finding out the ďwrongĒ amount of locktite to put between the tip of the grub screw and the flat side of the shaft. To little and it doesnít hold, too much and the pinion...
  8. I have always had great luck with Savox 1258tg...

    I have always had great luck with Savox 1258tg with the vxl-3s esc.
  9. Thread: XO-1 Diff

    by TwoBelugas
    Replies
    13
    Views
    305

    It would actually raise your car because the xo-1...

    It would actually raise your car because the xo-1 towers are the same heigh as your front so it will jack up your rear.

    Your best bet is to mount your shocks so the top is all the way in and...
  10. Replies
    5
    Views
    409

    Which rally, the old 1/10 that was discontinued...

    Which rally, the old 1/10 that was discontinued or the fiesta rally? You can make you own old 1/10 relatively easily with a few parts for bumpers and body mounts and a body from delta plastik. If the...
  11. If you had your mind set on the traxxas ones why...

    If you had your mind set on the traxxas ones why did you even bother asking? No one in the thread recommended the traxxas cvds.
  12. Replies
    16
    Views
    514

    I just remembered that the xo-1 wheels require...

    I just remembered that the xo-1 wheels require the traxxas notched 17mm hexes so if you have aftermarket six flat sided hexes the xo-1 wheels wont fit.
  13. Tekno m6 for fast on and off road driving set up,...

    Tekno m6 for fast on and off road driving set up, mip x duty for hard jumps and landings. Don’t forget to upgrade the diff gears to 6882x and heavier fluids if you have the budget.
  14. Replies
    4
    Views
    209

    Mount the stock shocks with the top in the inner...

    Mount the stock shocks with the top in the inner most hole and bottom in the out most hole gets the car pretty dang low, try that first and play with fluid weight and preload spacers first, if that...
  15. Replies
    16
    Views
    514

    I just use Flickr and set all my photos to...

    I just use Flickr and set all my photos to private unless using a shared link. Works great.
  16. Replies
    9
    Views
    291

    That looks like the older 4x4 vxl from some years...

    That looks like the older 4x4 vxl from some years ago. Someone more knowledgeable can tell you when they added tsm.

    The new ultimate will have a lot of upgrade parts already installed that would...
  17. Replies
    9
    Views
    291

    How can option 1 be without tsm? That’s built...

    How can option 1 be without tsm? That’s built into the radio receiver and unless the seller is taking away the receiver too, he doesn’t have that specific model

    Sorry to hear the high cost, is it...
  18. Replies
    16
    Views
    514

    You know, I bet the xo-1 tires being taller and...

    You know, I bet the xo-1 tires being taller and the wheels having more offset would fill those wheel wells nicely...
  19. Thread: Servo Horn

    by TwoBelugas
    Replies
    9
    Views
    297

    I would add that keep an eye on overall length...

    I would add that keep an eye on overall length and offset of the two holes. There is very little clearance on the LCG chassis on one side of the servo, that if a horn exceed a certain length and too...
  20. Replies
    4
    Views
    254

    Not sure if they made a running change at some...

    Not sure if they made a running change at some point but the xo-1 front tower is now different than the rear, part number 6440
    ...
  21. Replies
    36
    Views
    1,030

    I love mine thatís similarly set up. Does...

    I love mine thatís similarly set up. Does standing backflips on 2s, the stock vxl-3s and 3500 motor has been good for my usage.
  22. Replies
    15
    Views
    535

    This. I neve run my 2.4gz antena wires sticking...

    This. I neve run my 2.4gz antena wires sticking out like that, but rather let them sit upright inside the tube and put a plastic cap on the tube end. Range has never been a concern for me unless I...
  23. ^i second Steve, without a photo it’s impossible...

    ^i second Steve, without a photo it’s impossible for anyone to say what it is.

    Op, are you by any chance mounting the shock on the inner most hole on the a arm that was supposed to be for the...
  24. Replies
    10
    Views
    608

    I can work with barely. :D

    I can work with barely. :D
  25. Replies
    10
    Views
    608

    Thanks for the info. Was 25/31 with a 40mm can or...

    Thanks for the info. Was 25/31 with a 40mm can or 36mm can?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4